English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa MINI & MINI+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 48 / 55 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author warping , lifting prints Od kenatno10 on May 21, 20 1528 1 kenatno10 Colorisation with transparant filament Answered Od Crawlerin on May 20, 20 1431 4 Oxygen Prusa Mini freezes at 95% on Purge Od MCMuckle on May 19, 20 2565 4 3DPrintsbyChr... Trying to identify layer shift in x-axis Od LE3D on May 19, 20 2230 3 LE3D Mesh Bed Leveling Fails Od criageek on May 19, 20 2060 3 criageek Mini print evaluation Od Josh on May 17, 20 1251 1 Josh Heavy Stringing Od JoanTabb on May 17, 20 2228 2 kairikitty Extruder clicking during support material prin... Od kevman on May 17, 20 1536 1 kevman Large Live-Z but good first layer Od Milos V. on May 17, 20 2339 6 jaychatt Assembly Step 14 - M3x20 won't engage Od IamPeterYouAre... on May 15, 20 2545 6 griffinrevell Z Calibration failure Od karl-herbert on May 14, 20 1479 3 Glen Childres... Prusa mini Assembly issue with XZ electronics ... Od 3Dprintedgr on May 14, 20 2146 5 TechGuy2020 First time setup best practices Od Codetoad on May 11, 20 1630 3 Codetoad Some blobbing happening with prints. Od 3Dprintedgr on May 10, 20 1791 2 kevman Cannot get to the PTFE Tube Od reddadsteve on May 07, 20 2121 7 ari.s.friedma... Troubles with underextrusion Od bobc on May 07, 20 2623 9 Jens Kjeldste... Y belt not tensionned Od Ordimans on May 03, 20 1871 3 Ordimans Wiring for attaching Y AXIS motor does not mat... Od 3Dprintedgr on May 03, 20 1877 4 grabnerwg@gma... Wiring for attaching Y AXIS motor does not mat... Od grabnerwg@gmai... on May 03, 20 1731 5 grabnerwg@gma... Don't tighten the Z-Axis screws to much Od dargul on May 02, 20 2063 1 dargul Stránka 48 / 55 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Další Share: