English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa MINI & MINI+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 25 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Tytuł Tematu Ostatni Post Widok Posty Author Actual temperature of steel sheet? Przez cwbullet on Sep 05, 21 1464 2 Torc Torr Top layer under extrusion and extruder issues Answered Przez strangnet on Sep 03, 21 3546 7 strangnet PINDA height Przez jcjames_13009 on Sep 03, 21 1563 2 alidaf Put in filament, now extruding issues Przez jcjames_13009 on Sep 02, 21 2104 7 Pandak97 Overextruding and burning filament with Overtu... Przez Diem on Aug 31, 21 3112 5 Alyssa I Really Don't Know What's Gone Wrong Here? Przez Diem on Aug 31, 21 1220 5 Numbuh1Nerd First layer calibration problems Przez bryanweaver53 on Aug 31, 21 1821 8 bryanweaver53 Mini+, Can't figure out First Layer Calibratio... Przez JMH714 on Aug 31, 21 2554 9 Bjorn trapezoidal nut kit problems Przez JMH714 on Aug 31, 21 1867 5 foamflyer Mini Plus Assembly Kit. Verification All good.... Przez cwbullet on Aug 29, 21 1291 6 Nelson Poor print quality on narrow details - ideas Przez F0erster on Aug 29, 21 2355 5 RedTar First Prints With Stringy Edges / Messy First ... Przez cwbullet on Aug 29, 21 3619 10 Daniel Prusa mini, Loud Stepper Motors Przez Torc Torr on Aug 29, 21 4486 17 Cinnamon - Be... Mini+ Extrusion Issues Przez JMH714 on Aug 28, 21 1604 4 Mars Print Issues - Blobby Rough Patches Przez cwbullet on Aug 28, 21 1540 2 Parzival Vertical Scars Przez cwbullet on Aug 28, 21 1584 2 CommanderMoos... Looking for hints to what is causing PETG firs... Przez PrinterJohn on Aug 26, 21 1877 3 PrinterJohn Stringy Prints On 2 of 5 Prusa Mini+ Printers Przez GRIT Automatio... on Aug 23, 21 1948 5 GRIT Automati... Printer stops near the end Answered Przez Lupin on Aug 23, 21 1577 4 3dprintershop... New printer fails calibration on x axis Przez cwbullet on Aug 23, 21 1379 7 Stecco Strona 25 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Share: