Volker – Activité – Prusa3D Forum

Notifications

Clear all

Volker

Groupe: Enregistré

A(ont) rejoint: 2018/12/07

Estimable Member

	You can slice with the standard MK4 setting and send it to t... Dans le forum Input Shaper (MK4)	il y a 3 years
	The good news: even with those nasty stringing the print wor... Dans le forum General discussion, announcements and releases	il y a 3 years
	Tuning the filament tip is not an issue of the MMU3 vs MMU2.... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	On my printer: X: 42 Hz Y: 41.2 Hz Hard to see and even more... Dans le forum Input Shaper (MK4)	il y a 3 years
	Just printed all parts for the MMU3. In comparison to the pr... Dans le forum Input Shaper (MK4)	il y a 3 years
	What are you dreaming about. Prusa is nothing else a company... Dans le forum General discussion, announcements and releases	il y a 3 years
	Prusa troubleshooting: Clogged hotend (MK4) \| Prusa Knowledg... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	M201 sets the max acceleration limit. If the acceleration is... Dans le forum Input Shaper (MK4)	il y a 3 years
	On the MK3 I do not have the high speed of the MK4 and I onl... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	My Measurement is: X: 42 Hz Y: 41.2 Hz The given 30.5 is an ... Dans le forum Input Shaper (MK4)	il y a 3 years
	As described in the parallel thread: it is all in the gcode:... Dans le forum Input Shaper (MK4)	il y a 3 years
	There are two things you can do: Increase belt tension. At l... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	I used the "ringing tower" and instruction on: Input Shapi... Dans le forum Input Shaper (MK4)	il y a 3 years
	from buttom to top: medium, high and very high tension (what... Dans le forum Input Shaper (MK4)	il y a 3 years
	From buttom to top: regular tension; high tension; very high... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	Try to increase the y-belt tension (even higher than propose... Dans le forum Input Shaper (MK4)	il y a 3 years
	I got it improved by increasing the tension of the y-belt - ... Dans le forum Assembly and first prints troubleshooting	il y a 3 years
	One more item or problem I posted here:Vibration artefacts o... Dans le forum Input Shaper (MK4)	il y a 3 years
	The positive side: you can cut down the printing time withou... Dans le forum Input Shaper (MK4)	il y a 3 years
	Vibration artefacts on Y-Axis Dans le forum Assembly and first prints troubleshooting	il y a 3 years

Page 7 / 9 Précédent Suivant

Statistiques du forum

598 Forums

71.4 K Sujets

501 K Messages

13 En-ligne

82.3 K Membres

Le dernier des messages: Prusa CORE One INDX – Unmatched Toolchanger With 8 Nozzles – Orders Now Open! Notre nouveau membre: Jon Troiano Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé