SeattleDavid – Activité

Notifications

Clear all

SeattleDavid

Groupe: Enregistré

A(ont) rejoint: 2020/01/09

Estimable Member

	Is there a way to auto-select the filament? (Avoid prompt at... Dans le forum Hardware, firmware and software help	il y a 4 years
	I don't know about rotating the part. But the shift is unpre... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Layer Shifting: What are typical causes and solutions? Dans le forum How do I print this? (Printing help)	il y a 4 years
	@enzo-m I’m one of those persons who changes the oil in thei... Dans le forum General discussion, announcements and releases	il y a 4 years
	You don't play fair, do you? The SINGLE topic here is how to... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I beg to differ: Fresh install of Prusa Slicer 2.2, factory ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Let's stick with the correct facts and avoid the snide "Good... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I had a convenient photo of the black spool. I used it to il... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Your advice please? (How would you fix this?) Dans le forum How do I print this? (Printing help)	il y a 4 years
	@nilok I ONLY run with 7x7 bed leveling. As I have mentioned... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I am using Prusament. Only. Since Prusaslicer 2.2 is now out... Dans le forum How do I print this? (Printing help)	il y a 4 years
	FilamentOne was a good suggestion--yes FREE shipping and in ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	These are very helpful comments. Thank you! I am still quite... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I appreciate the diagram and input about leaking and speed.G... Dans le forum How do I print this? (Printing help)	il y a 4 years
	No, that link is just bullying. It is off topic, irrelevant,... Dans le forum How do I print this? (Printing help)	il y a 4 years
	No, I won't be bullied. There is a difference between "troll... Dans le forum How do I print this? (Printing help)	il y a 4 years
	So back to the question at hand: Where does this stuff come ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@bobstro Pointing out alternate sources of supply is great. ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	So back to the question at hand: Where does this stuff come ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@nilok Arguing with people who keep pressing upon me a polit... Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 10 / 13 Précédent Suivant

Statistiques du forum

559 Forums

62.1 K Sujets

439 K Messages

19 En-ligne

67.2 K Membres

Le dernier des messages: ASA Adhesion Issue on New G10 Plate Notre nouveau membre: Gajowy Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé