SeattleDavid – Aktivität

Benachrichtigungen

Alles löschen

SeattleDavid

Gruppe: Registriert

Beigetreten: 2020/01/09

Estimable Member

	Is there a way to auto-select the filament? (Avoid prompt at... Im Forum Hardware, firmware and software help	Vor 4 years
	I don't know about rotating the part. But the shift is unpre... Im Forum How do I print this? (Printing help)	Vor 4 years
	Layer Shifting: What are typical causes and solutions? Im Forum How do I print this? (Printing help)	Vor 4 years
	@enzo-m I’m one of those persons who changes the oil in thei... Im Forum General discussion, announcements and releases	Vor 4 years
	You don't play fair, do you? The SINGLE topic here is how to... Im Forum How do I print this? (Printing help)	Vor 4 years
	I beg to differ: Fresh install of Prusa Slicer 2.2, factory ... Im Forum How do I print this? (Printing help)	Vor 4 years
	Let's stick with the correct facts and avoid the snide "Good... Im Forum How do I print this? (Printing help)	Vor 4 years
	I had a convenient photo of the black spool. I used it to il... Im Forum How do I print this? (Printing help)	Vor 4 years
	Your advice please? (How would you fix this?) Im Forum How do I print this? (Printing help)	Vor 4 years
	@nilok I ONLY run with 7x7 bed leveling. As I have mentioned... Im Forum How do I print this? (Printing help)	Vor 4 years
	I am using Prusament. Only. Since Prusaslicer 2.2 is now out... Im Forum How do I print this? (Printing help)	Vor 4 years
	FilamentOne was a good suggestion--yes FREE shipping and in ... Im Forum How do I print this? (Printing help)	Vor 4 years
	These are very helpful comments. Thank you! I am still quite... Im Forum How do I print this? (Printing help)	Vor 4 years
	I appreciate the diagram and input about leaking and speed.G... Im Forum How do I print this? (Printing help)	Vor 4 years
	No, that link is just bullying. It is off topic, irrelevant,... Im Forum How do I print this? (Printing help)	Vor 4 years
	No, I won't be bullied. There is a difference between "troll... Im Forum How do I print this? (Printing help)	Vor 4 years
	So back to the question at hand: Where does this stuff come ... Im Forum How do I print this? (Printing help)	Vor 4 years
	@bobstro Pointing out alternate sources of supply is great. ... Im Forum How do I print this? (Printing help)	Vor 4 years
	So back to the question at hand: Where does this stuff come ... Im Forum How do I print this? (Printing help)	Vor 4 years
	@nilok Arguing with people who keep pressing upon me a polit... Im Forum How do I print this? (Printing help)	Vor 4 years

Seite 10 / 13 Vorherige Nächstes

Forums-Statistiken

559 Foren

62.1 K Themen

439 K Beiträge

17 Online

67.2 K Mitglieder

Letzter Beitrag: ASA Adhesion Issue on New G10 Plate Unser neuestes Mitglied: Gajowy Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen