SeattleDavid – Actividad

Avisos

Vaciar todo

SeattleDavid

Grupo: Registrado

Registrado: 2020/01/09

Estimable Member

	Is there a way to auto-select the filament? (Avoid prompt at... En el foro Hardware, firmware and software help	hace 4 years
	I don't know about rotating the part. But the shift is unpre... En el foro How do I print this? (Printing help)	hace 4 years
	Layer Shifting: What are typical causes and solutions? En el foro How do I print this? (Printing help)	hace 4 years
	@enzo-m I’m one of those persons who changes the oil in thei... En el foro General discussion, announcements and releases	hace 4 years
	You don't play fair, do you? The SINGLE topic here is how to... En el foro How do I print this? (Printing help)	hace 4 years
	I beg to differ: Fresh install of Prusa Slicer 2.2, factory ... En el foro How do I print this? (Printing help)	hace 4 years
	Let's stick with the correct facts and avoid the snide "Good... En el foro How do I print this? (Printing help)	hace 4 years
	I had a convenient photo of the black spool. I used it to il... En el foro How do I print this? (Printing help)	hace 4 years
	Your advice please? (How would you fix this?) En el foro How do I print this? (Printing help)	hace 4 years
	@nilok I ONLY run with 7x7 bed leveling. As I have mentioned... En el foro How do I print this? (Printing help)	hace 4 years
	I am using Prusament. Only. Since Prusaslicer 2.2 is now out... En el foro How do I print this? (Printing help)	hace 4 years
	FilamentOne was a good suggestion--yes FREE shipping and in ... En el foro How do I print this? (Printing help)	hace 4 years
	These are very helpful comments. Thank you! I am still quite... En el foro How do I print this? (Printing help)	hace 4 years
	I appreciate the diagram and input about leaking and speed.G... En el foro How do I print this? (Printing help)	hace 4 years
	No, that link is just bullying. It is off topic, irrelevant,... En el foro How do I print this? (Printing help)	hace 4 years
	No, I won't be bullied. There is a difference between "troll... En el foro How do I print this? (Printing help)	hace 4 years
	So back to the question at hand: Where does this stuff come ... En el foro How do I print this? (Printing help)	hace 4 years
	@bobstro Pointing out alternate sources of supply is great. ... En el foro How do I print this? (Printing help)	hace 4 years
	So back to the question at hand: Where does this stuff come ... En el foro How do I print this? (Printing help)	hace 4 years
	@nilok Arguing with people who keep pressing upon me a polit... En el foro How do I print this? (Printing help)	hace 4 years

Página 10 / 13 Anterior Siguiente

Estadísticas del Foro

559 Foros

62.1 K Temas

439 K Respuestas

18 En línea

67.2 K Miembros

Último Mensaje: ASA Adhesion Issue on New G10 Plate Nuestro miembro más reciente: Gajowy Últimos Mensajes Publicaciones sin leer Etiquetas

Iconos del foro: El foro no contiene publicaciones sin leer El foro contiene publicaciones sin leer

Iconos de los Temas: No respondidos Respondido Activo Popular Fijo No aprobados Resuelto Privado Cerrado