|
Prusa only sells the Nextruder for the XL at a price of abou... Dans le forum Hardware, firmware and software help |
il y a 1 year |
|
Actually new mk3s+ are shipped with the new frame. So the mk... Dans le forum General discussion, announcements and releases |
il y a 2 years |
|
I have not tested it yet, but as far as I remember there is ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
First I simply just put the black cable into a dupond 1-pin ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
While it is possible, I personally never ever have seen a co... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Actually the reason theese functions are missing is Prusa Re... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Yes, it is the black wire. It is always ground being switche... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Actually I Last compiled Prusa Mini firmware about 1 1/2 yea... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Das Bondtech upgrade ist nicht zwingend. Durch die 3:1 Unter... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 3 years |
|
Ich benutze seit Jahren den Bondtech upgrade extruder - aber... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 3 years |
|
Actually I use M221 a lot. While the z-offset is for optimal... Dans le forum General discussion, announcements and releases |
il y a 3 years |
|
In german settings it is called "Extrusionsfactor", in the d... Dans le forum General discussion, announcements and releases |
il y a 3 years |
|
Its better known as flowrate if I understand correctly. Da h... Dans le forum General discussion, announcements and releases |
il y a 3 years |
|
There is an option "XY slice compensation" in Print Settings... Dans le forum General discussion, announcements and releases |
il y a 3 years |
|
As I described, just add as many skirtlines as you have virt... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Das sehe ich grundsätzlich genauso. Da aber Nylon ziemlich h... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 3 years |
|
Die gelbe Leitung liefert die am Lüfter gemessene Drehzahl. ... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 3 years |
|
SWD, DIO, CLK and RST are the typical pins for JTAG connecti... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
J21 Pin 1 (CLK) and Pin 2 (GND) are connected with a Jumper ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
You can also set a z-offset in Prusa Slicer in printer setti... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
