Josef Průša – Aktywność

Notifications

Clear all

Josef Průša

Grupa: Admin

Dołączył: 2015/04/26

Tytuł: Member Admin

	100C je v poradku. Myslim ze budete mit spatne nastavenou vy... In forum Rady k tisku (Archiv)	9 years temu
	We use E3D V6Lite so it is compatible 🙂 Check out my print... In forum Prusa i3 kit (Archive)	9 years temu
	No, you just unscrew the extruder idler and then try to put ... In forum Prusa i3 kit (Archive)	9 years temu
	Glad to hear that! It's free workout bundled with every prin... In forum Prusa i3 kit (Archive)	9 years temu
	Check if you've got the hobbed pulley aligned precisely with... In forum Prusa i3 kit (Archive)	9 years temu
	V driverech 1.6.0 je nastavená teplota na 255 a 210 aby na 1... In forum Software (Archiv)	9 years temu
	Tiskne nám tu soustavně okolo 30 tiskáren, všechny z SD. Pok... In forum Stavebnice Prusa i3 (Archiv)	9 years temu
	Je termistor pevne uchyceny v hlinikovem bloku? Pokud nema z... In forum Stavebnice Prusa i3 (Archiv)	9 years temu
	Dobry den, potreboval bych videt fotku. In forum Rady k tisku (Archiv)	9 years temu
	When you removed it from the block, were the readings same? ... In forum Prusa i3 kit (Archive)	9 years temu
	It's not about how tight is the belt, but if the pulley is s... In forum Prusa i3 kit (Archive)	9 years temu
	Zkuste tisk na LCD zpomalit nebo zrychlit. Korkový motor se ... In forum Stavebnice Prusa i3 (Archiv)	9 years temu
	If you carefully unscrew the screw holding the thermistor in... In forum Prusa i3 kit (Archive)	9 years temu
	Are the belt pulleys on the motor shafts tight enough? If no... In forum Prusa i3 kit (Archive)	9 years temu
	Yeah, I wanted to make an option in the installer to install... In forum Prusa i3 kit (Archive)	9 years temu
	Hi, not the end of the world. You just forgot to tighten the... In forum Prusa i3 kit (Archive)	9 years temu
	Soucastkam vygenerujte g-code dle vaseho materialu ve Slic3r... In forum Stavebnice Prusa i3 (Archiv)	9 years temu
	Mate doma multimetr? Mohl by jste zmerit odpor thermistoru p... In forum Stavebnice Prusa i3 (Archiv)	9 years temu
	Contact us thru email, well check what is going on. Seems li... In forum Prusa i3 kit (Archive)	9 years temu
	Are you sure you are not trying to print a g-code for 3mm ve... In forum Prusa i3 kit (Archive)	9 years temu

Strona 30 / 39 Wstecz Następny

Statystyki Forum

565 Fora

63.9 K Tematy

447.6 K Posty

22 Online

69.5 K Członkowie

Ostatni Post: Faulty Top Layer Najnowszy użytkownik:: SilenceDIY Recent Posts Unread Posts Tags

Forum Icons: Forum contains no unread posts Forum contains unread posts

Ikony tematu: Not Replied Odwpowiedzi Aktywny Gorący Przyklejony Unapproved Rozwiązany Private Zamknięte