cwbullet – Activité – Prusa3D Forum

Notifications

Clear all

cwbullet

Groupe: PrusaLink-beta

A(ont) rejoint: 2018/07/13

Titre: Membre

	I will have to remember that one. I am not sure I have hear... Dans le forum Hardware, firmware and software help	il y a 4 years
	@ssill2 Looks a lot like stain glass. How hard was it to ge... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jerry-s Good news. Going to opposite direction and ignorin... Dans le forum Hardware, firmware and software help	il y a 4 years
	Is the light lighting up on the SPINDA on the last spot? Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@technical-ted Bingo. The purge line is not a good tell for... Dans le forum Hardware, firmware and software help	il y a 4 years
	That looks like a layer shift. Did you lubricate your beari... Dans le forum How do I print this? (Printing help)	il y a 4 years
	The image is a bit too close. It could be a layer shift but... Dans le forum Hardware, firmware and software help	il y a 4 years
	That is pretty slick! I am regretting going on vacation. I... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Have you contacted support via Chat? That is where I would ... Dans le forum Hardware, firmware and software help	il y a 4 years
	@kai-4 Nice find. I am going to have to install this one of... Dans le forum User mods - OctoPrint, enclosures, nozzles, ...	il y a 4 years
	@rjbram Make sure your nozzle is not too close to the bed. ... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	I would guess you are still too high. The only other thing ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@annier Did you prime it first? Ignore my question. I saw... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@annier That makes me happy. I do not have a daughter, but ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@annier What brand of ABS are you using? Dans le forum How do I print this? (Printing help)	il y a 4 years
	Check your grub screws. Did you lubricate you bearings? Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	You have a partial jam to your nozzle. You need to do a col... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	You have a partial jam to your nozzle. You need to do a col... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@ssill2 Ok. I have one roll of each of the clear PETGs. Dans le forum How do I print this? (Printing help)	il y a 4 years
	I have about 9-10 rolls of transparent PETG. If you nail do... Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 196 / 571 Précédent Suivant

Statistiques du forum

585 Forums

68.2 K Sujets

477.9 K Messages

12 En-ligne

76 K Membres

Le dernier des messages: Filament spool jumps off the holder Notre nouveau membre: ArtiVIVO Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé