cwbullet – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

cwbullet

Gruppe: PrusaLink-beta

Beigetreten: 2018/07/13

Titel: Mitglied

	I will have to remember that one. I am not sure I have hear... Im Forum Hardware, firmware and software help	Vor 4 years
	@ssill2 Looks a lot like stain glass. How hard was it to ge... Im Forum How do I print this? (Printing help)	Vor 4 years
	@jerry-s Good news. Going to opposite direction and ignorin... Im Forum Hardware, firmware and software help	Vor 4 years
	Is the light lighting up on the SPINDA on the last spot? Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@technical-ted Bingo. The purge line is not a good tell for... Im Forum Hardware, firmware and software help	Vor 4 years
	That looks like a layer shift. Did you lubricate your beari... Im Forum How do I print this? (Printing help)	Vor 4 years
	The image is a bit too close. It could be a layer shift but... Im Forum Hardware, firmware and software help	Vor 4 years
	That is pretty slick! I am regretting going on vacation. I... Im Forum How do I print this? (Printing help)	Vor 4 years
	Have you contacted support via Chat? That is where I would ... Im Forum Hardware, firmware and software help	Vor 4 years
	@kai-4 Nice find. I am going to have to install this one of... Im Forum User mods - OctoPrint, enclosures, nozzles, ...	Vor 4 years
	@rjbram Make sure your nozzle is not too close to the bed. ... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	I would guess you are still too high. The only other thing ... Im Forum How do I print this? (Printing help)	Vor 4 years
	@annier Did you prime it first? Ignore my question. I saw... Im Forum How do I print this? (Printing help)	Vor 4 years
	@annier That makes me happy. I do not have a daughter, but ... Im Forum How do I print this? (Printing help)	Vor 4 years
	@annier What brand of ABS are you using? Im Forum How do I print this? (Printing help)	Vor 4 years
	Check your grub screws. Did you lubricate you bearings? Im Forum Assembly and first prints troubleshooting	Vor 4 years
	You have a partial jam to your nozzle. You need to do a col... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	You have a partial jam to your nozzle. You need to do a col... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	@ssill2 Ok. I have one roll of each of the clear PETGs. Im Forum How do I print this? (Printing help)	Vor 4 years
	I have about 9-10 rolls of transparent PETG. If you nail do... Im Forum How do I print this? (Printing help)	Vor 4 years

Seite 196 / 571 Vorherige Nächstes

Forums-Statistiken

585 Foren

68.2 K Themen

478 K Beiträge

12 Online

76 K Mitglieder

Letzter Beitrag: 6.4.0-alpha Firmware for Prusa CORE One Unser neuestes Mitglied: ArtiVIVO Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen