Baklin – Activité – Prusa3D Forum

Notifications

Clear all

Baklin

Groupe: Enregistré

A(ont) rejoint: 2020/09/13

Reputable Member

	Sorry. Not sure how I did that. Here is a new zip file with ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I got it working again. I have no idea why but somehow somet... Dans le forum How do I print this? (Printing help)	il y a 4 years
	The old gcode still works and that was sliced with the same ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I have tried to slice the same STL file again today, but whe... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I had a look at the knowledge base. Have you re installed ... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	I think it is shown in the manual for the y axis but not for... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	Do all the axis move all the way? Do the printed parts of th... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	I don't hear any clicking in the video. But it is normal th... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	You do that with the springloaded screw at the left side of ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Also check for more instructions here:/p> Reducing the ten... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I just sliced it in 2.3 rc2 without problems with the same s... Dans le forum How do I print this? (Printing help)	il y a 4 years
	That is why I wanted to test it too. I don't think I will ev... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Step 5 (step 4 in the MK3s manual) in the X-axis assembly is... Dans le forum Hardware, firmware and software help	il y a 4 years
	I'm not sure about the G-code. But the SuperPinda doesn't ha... Dans le forum Hardware, firmware and software help	il y a 4 years
	The printed parts of the MK3s+ extruder are a little differe... Dans le forum General discussion, announcements and releases	il y a 4 years
	The manual you linked to is for the MK3s, not for the MK3s+ ... Dans le forum Hardware, firmware and software help	il y a 4 years
	I tried it again with -3 instead of the 3 in the picture I p... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I tried printing it, but that didn't work. It cuts of a part... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I found the instructions and a sample file on myminifactory.... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I made a quick 216mm model and tried it in PrusaSlicer. The... Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 18 / 22 Précédent Suivant

Statistiques du forum

559 Forums

62.5 K Sujets

441 K Messages

19 En-ligne

66.6 K Membres

Le dernier des messages: Odd slicing problem with new 2.8.1 brim-thickness draft shield Notre nouveau membre: Kyle Cornelius Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé