Baklin – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

Baklin

Gruppe: Registriert

Beigetreten: 2020/09/13

Reputable Member

	Sorry. Not sure how I did that. Here is a new zip file with ... Im Forum How do I print this? (Printing help)	Vor 4 years
	I got it working again. I have no idea why but somehow somet... Im Forum How do I print this? (Printing help)	Vor 4 years
	The old gcode still works and that was sliced with the same ... Im Forum How do I print this? (Printing help)	Vor 4 years
	I have tried to slice the same STL file again today, but whe... Im Forum How do I print this? (Printing help)	Vor 4 years
	I had a look at the knowledge base. Have you re installed ... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	I think it is shown in the manual for the y axis but not for... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	Do all the axis move all the way? Do the printed parts of th... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	I don't hear any clicking in the video. But it is normal th... Im Forum Assembly and first prints troubleshooting	Vor 4 years
	You do that with the springloaded screw at the left side of ... Im Forum How do I print this? (Printing help)	Vor 4 years
	Also check for more instructions here:/p> Reducing the ten... Im Forum How do I print this? (Printing help)	Vor 4 years
	I just sliced it in 2.3 rc2 without problems with the same s... Im Forum How do I print this? (Printing help)	Vor 4 years
	That is why I wanted to test it too. I don't think I will ev... Im Forum How do I print this? (Printing help)	Vor 4 years
	Step 5 (step 4 in the MK3s manual) in the X-axis assembly is... Im Forum Hardware, firmware and software help	Vor 4 years
	I'm not sure about the G-code. But the SuperPinda doesn't ha... Im Forum Hardware, firmware and software help	Vor 4 years
	The printed parts of the MK3s+ extruder are a little differe... Im Forum General discussion, announcements and releases	Vor 4 years
	The manual you linked to is for the MK3s, not for the MK3s+ ... Im Forum Hardware, firmware and software help	Vor 4 years
	I tried it again with -3 instead of the 3 in the picture I p... Im Forum How do I print this? (Printing help)	Vor 4 years
	I tried printing it, but that didn't work. It cuts of a part... Im Forum How do I print this? (Printing help)	Vor 4 years
	I found the instructions and a sample file on myminifactory.... Im Forum How do I print this? (Printing help)	Vor 4 years
	I made a quick 216mm model and tried it in PrusaSlicer. The... Im Forum How do I print this? (Printing help)	Vor 4 years

Seite 18 / 22 Vorherige Nächstes

Forums-Statistiken

559 Foren

62.5 K Themen

441 K Beiträge

18 Online

66.6 K Mitglieder

Letzter Beitrag: Odd slicing problem with new 2.8.1 brim-thickness draft shield Unser neuestes Mitglied: Kyle Cornelius Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen