Baklin – Actividad – Prusa3D Forum

Avisos

Vaciar todo

Baklin

Grupo: Registrado

Registrado: 2020/09/13

Reputable Member

	Sorry. Not sure how I did that. Here is a new zip file with ... En el foro How do I print this? (Printing help)	hace 4 years
	I got it working again. I have no idea why but somehow somet... En el foro How do I print this? (Printing help)	hace 4 years
	The old gcode still works and that was sliced with the same ... En el foro How do I print this? (Printing help)	hace 4 years
	I have tried to slice the same STL file again today, but whe... En el foro How do I print this? (Printing help)	hace 4 years
	I had a look at the knowledge base. Have you re installed ... En el foro Assembly and first prints troubleshooting	hace 4 years
	I think it is shown in the manual for the y axis but not for... En el foro Assembly and first prints troubleshooting	hace 4 years
	Do all the axis move all the way? Do the printed parts of th... En el foro Assembly and first prints troubleshooting	hace 4 years
	I don't hear any clicking in the video. But it is normal th... En el foro Assembly and first prints troubleshooting	hace 4 years
	You do that with the springloaded screw at the left side of ... En el foro How do I print this? (Printing help)	hace 4 years
	Also check for more instructions here:/p> Reducing the ten... En el foro How do I print this? (Printing help)	hace 4 years
	I just sliced it in 2.3 rc2 without problems with the same s... En el foro How do I print this? (Printing help)	hace 4 years
	That is why I wanted to test it too. I don't think I will ev... En el foro How do I print this? (Printing help)	hace 4 years
	Step 5 (step 4 in the MK3s manual) in the X-axis assembly is... En el foro Hardware, firmware and software help	hace 4 years
	I'm not sure about the G-code. But the SuperPinda doesn't ha... En el foro Hardware, firmware and software help	hace 4 years
	The printed parts of the MK3s+ extruder are a little differe... En el foro General discussion, announcements and releases	hace 4 years
	The manual you linked to is for the MK3s, not for the MK3s+ ... En el foro Hardware, firmware and software help	hace 4 years
	I tried it again with -3 instead of the 3 in the picture I p... En el foro How do I print this? (Printing help)	hace 4 years
	I tried printing it, but that didn't work. It cuts of a part... En el foro How do I print this? (Printing help)	hace 4 years
	I found the instructions and a sample file on myminifactory.... En el foro How do I print this? (Printing help)	hace 4 years
	I made a quick 216mm model and tried it in PrusaSlicer. The... En el foro How do I print this? (Printing help)	hace 4 years

Página 18 / 22 Anterior Siguiente

Estadísticas del Foro

565 Foros

63.9 K Temas

447.7 K Respuestas

19 En línea

69.6 K Miembros

Último Mensaje: Built-in Calibration Tools Nuestro miembro más reciente: Mechman0124 Últimos Mensajes Publicaciones sin leer Etiquetas

Iconos del foro: El foro no contiene publicaciones sin leer El foro contiene publicaciones sin leer

Iconos de los Temas: No respondidos Respondido Activo Popular Fijo No aprobados Resuelto Privado Cerrado