Notifications
Clear all

Show your enclosures  

Page 7 / 8
  RSS
Owens2303
(@owens2303)
Eminent Member
RE: Show your enclosures

I also have not reached above 36 Celsius in my enclosure printing ABS either

 

Publié : 22/03/2021 11:35 pm
Robeena Shepherd
(@robeena-shepherd)
Estimable Member
RE: Show your enclosures

I finally got around to releasing everything (I think it's everything) I used to build my enclosure on page 4:

https://www.prusaprinters.org/prints/66830-prusa-mini-enclosure

 

Publié : 15/05/2021 12:30 pm
John Doe
(@john-doe-3)
Estimable Member
RE: Show your enclosures

I already twice torn the doors, when doing something with printer (maintenance).

Has someone seen a ikea lack (v1) with roll/pushdown door, just like garages have, but with plexiglass ?

 

Publié : 13/06/2021 5:46 am
mark
 mark
(@mark-3)
Reputable Member
RE: Show your enclosures

@john-doe-3

That's what I did. It's a simple piece of plexiglass that is captured by some clips and slides up and down. It is a little rough, but serviceable.

https://sites.google.com/view/newbieprusaminireview/home

Regards,

Mark

Publié : 13/06/2021 6:03 am
John Doe a aimé
John Doe
(@john-doe-3)
Estimable Member
RE: Show your enclosures

@mark-6

Looks nice. But because I have already split the "front" plexiglass, I do not want to go with this. And wife use the top of the Ikea Lack for her things 🙁 ... 

Publié : 13/06/2021 6:50 am
John Doe
(@john-doe-3)
Estimable Member
RE: Show your enclosures

Was thinking something like this... https://www.thingiverse.com/thing:4867501    ... cut plexiglass to 5cm x 44cm , tape together. Print leading rails, basically one vertical, one horizontal and a quarter of circle for each side. If the rotation and stress on plexiglass is high, then either print some extension on the plexiglass or higher diameter of the rails.

Publié : 13/06/2021 8:42 am
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Show your enclosures

@mark-6

I'm always amazed at the effort people go to in order to give the printer a warm lounge 👍 

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Publié : 13/06/2021 9:50 am
fuchsr a aimé
fuchsr
(@fuchsr)
Famed Member
RE: Show your enclosures

@john-doe-3

I have a hard time seeing how acrylic can be bent so much to allow what you're trying to accomplish. 

But I understand they the doors always seem to be in the way. Last night I actually started printing parts for this variant of the Lack enclosure: https://www.thingiverse.com/thing:3485510 for my next printer. I like the way you can slide the doors out of the way. 

i just printed the first batch of components so I can't vouch for its performance. 

Publié : 13/06/2021 10:00 am
John Doe
(@john-doe-3)
Estimable Member
RE: Show your enclosures

@fuchsr

I was thinking something like this to add. 

Publié : 13/06/2021 11:13 am
cwbullet
(@cwbullet)
Membre
RE: Show your enclosures

@john-doe-3

Very nice design.  You should test it out and add it to the world.  

--------------------
Chuck H
3D Printer Review Blog

Publié : 13/06/2021 11:23 am
mark
 mark
(@mark-3)
Reputable Member
RE: Show your enclosures
Posted by: @karl-herbert

@mark-6

I'm always amazed at the effort people go to in order to give the printer a warm lounge 👍 

It is not so much for temperature as to exhaust the fumes outside and have the enclosure inside. It's supposed to reach 47 C this week. Inside, the HVAC is set to 25C so cooling is not too expensive.

Regards,

Mark

Publié : 13/06/2021 12:43 pm
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Show your enclosures

@mark-6

Do you live in a desert (47 degrees C.)? 😊 

wbr,

Karl

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Publié : 13/06/2021 1:26 pm
mark
 mark
(@mark-3)
Reputable Member
RE: Show your enclosures

@karl-herbert

Yes, in the Phoenix, Arizona area. It has reached 50 C. I suppose there are a few warmer places.

Regards,

Mark

Publié : 13/06/2021 1:35 pm
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Show your enclosures

@mark-6

Then, of course, it makes sense to put the printer in an enclosure and provide a stable climate. 30-35 degrees C. is a good reference value for printing PETG or PLA. For ABS or similar it may be a little more.

happy printing,

Karl

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Publié : 13/06/2021 1:54 pm
obv
 obv
(@obv)
Eminent Member
RE: Show your enclosures

Not really an "enclosure" since there are no walls but this is my printer tower for both 2D and 3D jobs.

Publié : 29/06/2021 4:04 pm
BrettG
(@brettg)
Estimable Member
RE: enjoyable project

A small farm with no live stock 

Ce message a été modifié il y a 3 years 2 fois par BrettG
Publié : 27/07/2021 10:37 am
cwbullet
(@cwbullet)
Membre
Minis

 

Posted by: @brettg

A small farm with no live stock 

Nice rack of Minis.

--------------------
Chuck H
3D Printer Review Blog

Publié : 27/07/2021 5:39 pm
BrettG a aimé
cwbullet
(@cwbullet)
Membre
Cabinet

 

Posted by: @brettg

A small farm with no live stock 

What cabinet did you use to do that?

--------------------
Chuck H
3D Printer Review Blog

Publié : 27/07/2021 5:40 pm
BrettG
(@brettg)
Estimable Member
RE: response

 

Posted by: @cwbullet

 

Posted by: @brettg

A small farm with no live stock 

What cabinet did you use to do that?

Originally  https://www.ebay.co.uk/itm/312760792774?var=611487887584 then modified. which cable management on the rear for all the power supplies / led lighting, because its mobile on castors allowing me to move around my room and also to get to the rear. 

Ce message a été modifié il y a 3 years 2 fois par BrettG
Publié : 28/07/2021 7:04 am
cwbullet
(@cwbullet)
Membre
Wow

I did not recognize it.  You completely transformed it. 

Posted by: @brettg

 

Posted by: @cwbullet

 

Posted by: @brettg

A small farm with no live stock 

What cabinet did you use to do that?

Originally  https://www.ebay.co.uk/itm/312760792774?var=611487887584 then modified. which cable management on the rear for all the power supplies / led lighting, because its mobile on castors allowing me to move around my room and also to get to the rear. 

 

--------------------
Chuck H
3D Printer Review Blog

Publié : 28/07/2021 9:53 am
BrettG a aimé
Page 7 / 8
Partager :