| |
Topic Title |
Forum |
 |
teplota trysky By pavel puškár 7 hours ago | Last Post: 7 hours ago
|
Složení tiskárny a řešení potíží s prvním tiskem |
|
 |
New to 3d printing. Looking for resources By proX gaming 4 days ago | Last Post: 7 hours ago
|
General discussion, announcements and releases |
|
 |
Mid model filament change issue: z height reduction after change By Tim K 8 hours ago | Last Post: 8 hours ago
|
General discussion, announcements and releases |
|
 |
First | Initial Layer flow By Gatze 2 years ago | Last Post: 8 hours ago
|
PrusaSlicer |
|
 |
Kann Form aus Slicer nicht löschen By BrickTec - Lights 8 hours ago | Last Post: 8 hours ago
|
Hilfe zur Hardware, Firmware und Software |
|
|
|
Filament tangling every time when using the enclosure with Prusa PLA By Tim K 8 hours ago | Last Post: 8 hours ago
|
Assembly and troubleshooting |
|
 |
Probleme mit dem Slicer By Hai47 3 months ago | Last Post: 8 hours ago
|
Hilfe zur Hardware, Firmware und Software |
|
 |
Multi Material Issues By RobbieG 3 months ago | Last Post: 9 hours ago
|
How do I print this? (Printing help) |
|
 |
Revo High Flow 60W heater core on MK3S+ By Caelestis 3D 9 hours ago | Last Post: 9 hours ago
|
User mods - OctoPrint, enclosures, nozzles, ... |
|
|
|
Melting bottom carriage plate By L Y 12 hours ago | Last Post: 10 hours ago
|
General discussion, announcements and releases |
|
 |
Prusa Mini and MMU ? By Abbie 11 hours ago | Last Post: 10 hours ago
|
General discussion, announcements and releases |
|
 |
Why cant i upgrade a 3.5 to a 3.9 or 4 By Clinton 10 hours ago | Last Post: 10 hours ago
|
General discussion, announcements and releases |
|
 |
MK4 Nextruder blockiert auf X Achse By Marof 10 hours ago | Last Post: 10 hours ago
|
Hardware, firmware and software help |
|
 |
Now a bit apprehensive about my Mk4 kit By StinkyPete 1 week ago | Last Post: 11 hours ago
|
Assembly and first prints troubleshooting |
|
 |
How can I get my printer to work again. By tre4b 1 week ago | Last Post: 11 hours ago
|
How do I print this? (Printing help) |
|
 |
SL1S Potential Bug: print surface too big causing Tilt Homing Failed By V2arK 1 month ago | Last Post: 12 hours ago
|
General discussion, announcements and releases |
|
 |
Bard says the Bambu X1c swaps filaments faster than Prusa XL By SeattleDavid 5 months ago | Last Post: 12 hours ago
|
General discussion, announcements and releases |
|
 |
The importance of the filament detection sensor calibration (MK3S) and other problems By Nico2126 2 days ago | Last Post: 12 hours ago
|
Assembly and first prints troubleshooting |
|
 |
Filamatrix Phoenix Nylon filament By Good Printing 12 hours ago | Last Post: 12 hours ago
|
General discussion, announcements and releases |
|
 |
Setup PrusaSlicer for Ultimaker S5 By Vatuhiva 4 years ago | Last Post: 13 hours ago
|
PrusaSlicer |
|