Recent Posts
 
Notifications
Clear all

Recent Posts

Stránka 1 / 43
  Název Tématu Fórum
PCR Gcode for Chamber Fans and LED Light (1 viewing)

Od PCR před 8 hours  |  Poslední Příspěvek: před 1 min

Hardware, firmware and software help
 
aztravis1 Getting ready to chuck my MMU3, constant layer shifts on color changes

Od aztravis1 před 44 mins  |  Poslední Příspěvek: před 44 mins

General discussion, announcements and releases
 
Travi Convince me I need an XL

Od Travi před 2 days  |  Poslední Příspěvek: před 1 hour

General discussion, announcements and releases
 
Asus1357 layer shift on Y axis

Od Asus1357 před 1 day  |  Poslední Příspěvek: před 3 hours

How do I print this? (Printing help)
 
Leehound The Core One needs a very stable surface

Od Leehound před 17 hours  |  Poslední Příspěvek: před 4 hours

General discussion, announcements and releases
 
kevman Opening up the MMU3 to clear jams ?

Od kevman před 5 hours  |  Poslední Příspěvek: před 5 hours

Assembly and first prints troubleshooting
 
cristian Accelerometer Set

Od cristian před 5 days  |  Poslední Příspěvek: před 5 hours

General discussion, announcements and releases
 
Kapwinnnng Multiple colors on the same layer?

Od Kapwinnnng před 4 days  |  Poslední Příspěvek: před 7 hours

How do I print this? (Printing help)
 
MegardStudio Z callibration failure no matter where the PINDA is set or adjusted, even after replacing it.

Od MegardStudio před 2 months  |  Poslední Příspěvek: před 7 hours

Hardware, firmware and software help
 
Cloud1983 Bad Vibrations

Od Cloud1983 před 3 days  |  Poslední Příspěvek: před 8 hours

Hardware, firmware and software help
 
baztm VFA Artifacts on X+Y Straight Edges

Od baztm před 16 hours  |  Poslední Příspěvek: před 8 hours

Hardware, firmware and software help
 
Anthony Urbani Filament Flow Sensor?

Od Anthony Urbani před 8 hours  |  Poslední Příspěvek: před 8 hours

User mods - OctoPrint, enclosures, nozzles, ...
 
Luke2123 Impossible Print - Repeated Print Failures - Arctos Robot X Pulley

Od Luke2123 před 11 hours  |  Poslední Příspěvek: před 9 hours

How do I print this? (Printing help)
 
jrichels20 PrusaSlicer 2.9.0 Supports Question

Od jrichels20 před 11 hours  |  Poslední Příspěvek: před 9 hours

PrusaSlicer
 
BogoRin MK4S -> Core One conversion - reusable parts

Od BogoRin před 2 weeks  |  Poslední Příspěvek: před 9 hours

General discussion, announcements and releases
 
Buddhasbuddy PrusaSlicer 2.9.0 Colour Paint not slicing (1 viewing)

Od Buddhasbuddy před 14 hours  |  Poslední Příspěvek: před 10 hours

General software discussion
 
reox y-axis belt rubs against belt-idler side

Od reox před 3 months  |  Poslední Příspěvek: před 10 hours

Hardware, firmware and software help
 
latot Fine First layer calibration

Od latot před 2 weeks  |  Poslední Příspěvek: před 10 hours

Assembly and first prints troubleshooting
 
techfreek Core One MMU3 Prototypes

Od techfreek před 3 weeks  |  Poslední Příspěvek: před 10 hours

General discussion, announcements and releases
 
SteveS Banging plate X and Y stops

Od SteveS před 2 months  |  Poslední Příspěvek: před 11 hours

Hardware, firmware and software help
 
Stránka 1 / 43

 

 

 

Share: