| |
Topic Title |
Forum |
 |
Ideas for skew correction on a Core One By hyiger 2 weeks ago | Last Post: 2 days ago
|
General discussion, announcements and releases |
| |
|
 |
Z axis trouble but only when printing By ghostrider13 10 months ago | Last Post: 2 days ago
|
Assembly and first prints troubleshooting |
| |
|
 |
Prusa CORE One Dry Box By Scott 11 months ago | Last Post: 2 days ago
|
User mods |
| |
|
 |
Core One +: Auto Vent opening By Andhrimnir 4 days ago | Last Post: 2 days ago
|
General discussion, announcements and releases |
| |
|
 |
Under extrusion? at start of seam By Matt 1 week ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
 |
Initiale Kalibrierung - Z Achse bewegt sich nicht By NewMiraculix 3 days ago | Last Post: 2 days ago
|
Zusammenbau und Fehlersuche bei den ersten Druckversuchen |
| |
|
 |
Fehler #17819 nach Firmwareupdate auf 6.4.0 By Periz 1 month ago | Last Post: 2 days ago
|
Hilfe zur Hardware, Firmware und Software |
| |
|
|
|
Chyba teploty / thermal error By Michal Kahovec 3 years ago | Last Post: 2 days ago
|
Hardware, firmware a software (Pomoc) |
| |
|
 |
OUPS By Laurent 7 days ago | Last Post: 2 days ago
|
Aide concernant le matériel, le firmware ou un logiciel |
| |
|
|
|
Filament 'stuck', but not really after latest 6.4.0 By Danut Tabacaru 1 month ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
|
|
Display not working on MK4S By Rick Avra 2 days ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
 |
PrusaLink with a Pi 2b+?? By TheRedEyeBandit 3 days ago | Last Post: 2 days ago
|
General discussion & User Experience & Ideas |
| |
|
 |
problems with importing SVGs By j-martin 2 days ago | Last Post: 2 days ago
|
PrusaSlicer |
| |
|
 |
scarfjoint enforcer modifier By 4Thee 2 weeks ago | Last Post: 3 days ago
|
PrusaSlicer |
| |
|
 |
Core One LED light strips By bowtie6 5 months ago | Last Post: 3 days ago
|
User mods |
| |
|
 |
Buddy Camera in the Core one reads the code and shows up in Connect, but is not registered. By Dik Harrison 5 months ago | Last Post: 3 days ago
|
General discussion, announcements and releases |
| |
|
 |
Dryer connection By Phil 4 days ago | Last Post: 3 days ago
|
General discussion, announcements and releases |
| |
|
|
|
First Time Calibration - Z Level Error By NewMiraculix 3 days ago | Last Post: 3 days ago
|
Assembly and first prints troubleshooting |
| |
|
|
|
Failed First Print - Fix for PETG Benchy that shifted after a couple layers on textured sheet? By Stormy 1 week ago | Last Post: 3 days ago
|
Prints troubleshooting |
| |
|
|
|
Y-Achse Riemen spannen? Ich kapiere nicht wie? By Dominic Ruetsch 2 weeks ago | Last Post: 3 days ago
|
Hilfe zur Hardware, Firmware und Software |
| |
|