Recent Posts

Forums | Topics

Page 6 / 35 Prev Next

	Topic Title	Forum
	Problem z selftestem osi X By pangus 4 days ago \| Last Post: 4 days ago	Hardware, firmware i oprogramowanie - pomoc
	Witam, przychodzę tutaj z problemem, który nie jes... 4 days ago By pangu...
	Manually adjust heat bed thermister calibration temp??? By Dazz 4 days ago \| Last Post: 4 days ago	Hardware, firmware and software help
	Hi I have replaced my heat bed thermister but now ... 4 days ago By Dazz
	Prusa Slicer settings for Anycubic Kobra S1 By Nolan 4 days ago \| Last Post: 4 days ago	General discussion, announcements and releases
	Was wondering if anyone had suggestions or config ... 4 days ago By Nolan
	Strange issues on prints By vsions 4 days ago \| Last Post: 4 days ago	Assembly and first prints troubleshooting
	It's a combination of extreme overhang and the dir... 4 days ago By Diem Hello, I have been trying to figure out why my pri... 4 days ago By vsion...
	Chronic Under-Extrusion - Core ONE By PaltrySun 5 days ago \| Last Post: 4 days ago	General discussion, announcements and releases
	Once you have consistently dry filament (and possi... 4 days ago By Diem Thanks for the responses! I only used PLA and P... 4 days ago By Paltr... clicking/grinding filament and stringy filament Ag... 4 days ago By Diem view all posts
	PrusaConnect keeps showing OFFLINE and other connection issues By Roger 6 months ago \| Last Post: 4 days ago	Bugs & Errors
	Same here, when starting up everything shows ok, a... 4 days ago By sabre... I've been having the same issues with my Core One.... 2 weeks ago By Hammy I'm still getting these Offline statuses, been hap... 3 weeks ago By Chris view all posts
	Buddy Camera in the Core one reads the code and shows up in Connect, but is not registered. By Dik Harrison 1 month ago \| Last Post: 4 days ago	General discussion, announcements and releases
	I am having the same issue! Hope there's an answer... 4 days ago By Crise... That is correct. Any suggestions? 2 weeks ago By Dik H... Buddy Camera that’s linked to a Core device (maybe... 3 weeks ago By Deepa...
	Large ABS + PLA print, PLA keeps clogging By xatlas0 3 weeks ago \| Last Post: 4 days ago	General discussion, announcements and releases
	I experienced a similar issue with the combo of AS... 4 days ago By dawso... What's the best way to check size and roundness so... 2 weeks ago By Diem The three most likely causes: - Out of spec filame... 3 weeks ago By xatla... view all posts
	Core One skipping steps/Layer shift By Enrique Specht 6 months ago \| Last Post: 4 days ago	Hardware, firmware and software help
	I am having the exact same problem. The location o... 4 days ago By Jane ... I seem to have the same, or at least similar probl... 1 week ago By Marti... I am experiencing the same issue, with a printable... 2 weeks ago By wdvc view all posts
	Two head printing - Automatic switch By AAM Metaldyne 5 days ago \| Last Post: 4 days ago	How do I print this? (Printing help)
	You are looking for the Spooljoin function: Cheer... 4 days ago By Diem Hello, My compagny order a printer XL for indust... 5 days ago By AAM M...
	Core one firmware 6.4.0 alpha By Philippe BAUER 4 days ago \| Last Post: 4 days ago	Hardware, firmware and software help
	For the core one, concerning the phase stepping c... 4 days ago By Phili...
	Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App By Vincent5840 5 months ago \| Last Post: 4 days ago	Hardware, firmware and software help
	That's not entirely right. It may level the bed at... 4 days ago By CJD Thank you! 🙂 5 days ago By Timma... RE: Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App 5 days ago By Raine... view all posts
	MK4 Prusa Enclosure By Mullu 6 days ago \| Last Post: 4 days ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	danke für die schnelle Antwort. Ich bevorzuge die ... 4 days ago By Mullu Entweder den PTFE-Schlauch durch drücken von oben ... 5 days ago By Walte... Hallo, ich habe dieses Wochenende das Gehäuse für ... 6 days ago By Mullu
	CORE One: Funktion Türschalter? By M3T 1 week ago \| Last Post: 4 days ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Nach Kontakt mit Prusa des Rätsels Lösung: 1. Der ... 4 days ago By M3T Hallo, nach Inbetriebnahme des CORE One (Kalibrier... 1 week ago By M3T
	Strange issues on prints By vsions 4 days ago \| Last Post: 4 days ago	How do I print this? (Printing help)
	Hello, I have been trying to figure out why my pri... 4 days ago By vsion...
	File Transfer Error When Using Prusa Connect By gurgleapps 2 years ago \| Last Post: 5 days ago	Bugs & Errors
	I had this issue on my Mk3s+. Changing the sd card... 5 days ago By Eliza... Hi, I had the same problem as every one with the e... 5 months ago By Victo... I also had transfer errors, but after formatting t... 8 months ago By Ender... view all posts
	Strange rattling noise By Jamie Porro 4 weeks ago \| Last Post: 5 days ago	Hardware, firmware and software help
	I spent six weeks trying to get CoreOne to work pr... 5 days ago By J.J. ... I did initially have a minor issue with the cable ... 4 weeks ago By Laura... The Avoid Curling Overhangs setting causing issues... 4 weeks ago By Tim view all posts
	Webcam App to instantly view Buddy camera livestream in Core One By dmast 2 months ago \| Last Post: 5 days ago	General discussion, announcements and releases
	That must be it, thank you. From my iPhone, I was ... 5 days ago By CW That might be the problem. Guest WiFi networks oft... 7 days ago By tbr @tbr-2 I can't get this to work and I don't know w... 1 week ago By CW view all posts
	High Flow Nozzle compatability By Wilko 10 months ago \| Last Post: 5 days ago	Hardware, firmware and software help
	Hi Wilko, please what you mean by "profiles are al... 5 days ago By Jendi... You can indeed choose a "regular" nozzel for the M... 10 months ago By Wilko The mk4s has profiles for standard and high flow n... 10 months ago By vhubb...