Recent Posts

Forums | Topics

Page 21 / 34 Prev Next

	Topic Title	Forum
	Broken Hotend Thermistor Wire By Patrick 7 years ago \| Last Post: 3 weeks ago	Assembly and first prints troubleshooting
	Same issue the zip tie back was rubbing against th... 3 weeks ago By JMars Log into your Eshop account, navigate to Company, ... 2 years ago By Diem Did anyone come up with a solution for this??? I'm... 2 years ago By Chas ... view all posts
	Two suggestions for the Core One team By Laura F Farrell 3 weeks ago \| Last Post: 3 weeks ago	Assembly and first prints troubleshooting
	1. There's no check to ensure you've properly alig... 3 weeks ago By Laura...
	Input Shaper Calibration with ADXL345 By MustafaA 3 weeks ago \| Last Post: 3 weeks ago	User mods - OctoPrint, enclosures, nozzles, ...
	Hi, I've been working for a way to calculate Input... 3 weeks ago By Musta...
	Correct Workflow to add nozzle variants By sticilface 3 weeks ago \| Last Post: 3 weeks ago	PrusaSlicer
	I've got a core one. Two nozzles the 0.4mm HF noz... 3 weeks ago By stici...
	Nestabilní PrusaSlicer By Honza 3 weeks ago \| Last Post: 3 weeks ago	PrusaSlicer
	Snad již finálně vyřešeno. Nainstaloval jsem ovlad... 3 weeks ago By Honza Po instalaci nového Sliceru je opět nestabilní a p... 3 weeks ago By Honza Vyřešeno, po upgradu Win a několika restartech již... 3 weeks ago By Honza
	Problem with support attached to model By Rick 3 weeks ago \| Last Post: 3 weeks ago	User mods - Octoprint, Enclosures, Nozzles, ...
	Thanks Tim! This filament was new, so drying will ... 3 weeks ago By Rick You have a problem with the filament and extrusion... 3 weeks ago By Tim Problem with support attached to model 3 weeks ago By Rick
	Printer printing wrong g code file By GordonMcD 12 months ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I also have this issue. It seems to occur when the... 3 weeks ago By Johan... Yeah same issue here with my MK3S+ with firmware 3... 2 months ago By Beaco... I als0 have been having this problem...picking th... 2 months ago By Sally... view all posts
	neue Düsen passen nicht ohne Nachbearbeitung By Wolverine0815 3 weeks ago \| Last Post: 3 weeks ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Habe ich in dieser Größe noch nie gesehen. 3 weeks ago By Wolve... Wer Erfahrung hat mit der Mertallbearbeitung, kann... 3 weeks ago By Frick... Hallo zusammen,ich habe bei meinem MK4 bzw. jetzt ... 3 weeks ago By Wolve...
	Pin Holes By Bryan Powell 3 weeks ago \| Last Post: 3 weeks ago	How do I print this? (Printing help)
	Thank you for your reply Tim. The test part is 3 l... 3 weeks ago By Bryan... You didn't say how many layers are involved. But i... 3 weeks ago By Tim Hello, I am attempting to print a lightbox for a b... 3 weeks ago By Bryan...
	Better anti vibration feet alternative? By perky890 3 weeks ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	I had one of the original Core Ones and it came wi... 3 weeks ago By vhubb... +1. I used them on all my Core Ones. Work great 3 weeks ago By FoxRu... You can peel off the adhesive tape and glue them o... 3 weeks ago By hyige...
	MMU3 filament load failure By William Westbo 3 weeks ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	I have a MK4 that I upgraded to a MK4S and then I ... 3 weeks ago By Willi...
	Replacing hot end. 2 wires that I can't figure where they were. By GXS 2 months ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I've never seen wire like that on a Prusa. Perhap... 3 weeks ago By Tim which version of printer?i know on my mk3 there sh... 3 weeks ago By Sumta I had a failed ABS print that left the hot end enc... 2 months ago By GXS
	Are there any apps for testing g-code on a Core One By hyiger 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	FWIW, Octoprint on an rpi auto-selects 115200, Coo... 3 weeks ago By ssmit... Not trying to do anything other than understand wh... 3 weeks ago By hyige... Simply connect 15200,8,N,1 and sent send. Not sure... 3 weeks ago By Tim view all posts
	PrusaSlicer 2.9.3 Final is out By Petr Kubiš 3 weeks ago \| Last Post: 3 weeks ago	PrusaSlicer
	Tried to delete previous post, but update for fix.... 3 weeks ago By Danie... Well, this is awkward. Updated to this version and... 3 weeks ago By Danie... We released the final version of 2.9.3 last week! ... 3 weeks ago By Petr ...
	Unable to control printer with PRUSA App By mmmachnik 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I recently added a MMU3 to my Core ONE and now the... 3 weeks ago By mmmac...
	Camera jammed the print board By Justin Craigie 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	Wanted to add here that the Buddy camera magnets s... 3 weeks ago By hyige... Try a control/calibration/z-alignment? 3 weeks ago By ssmit... The buddy camera fell during a print and caused th... 3 weeks ago By Justi...
	MKS4 with mmu3 printed now will not By tweiner 3 weeks ago \| Last Post: 3 weeks ago	Assembly and first prints troubleshooting
	I have a MK4S with mmu3. I ordered assembled. Un... 3 weeks ago By twein...
	Looking for profiles for 3DXTech filaments By Steve 3 weeks ago \| Last Post: 3 weeks ago	PrusaSlicer
	Does anyone know where I can find PrusaSlicer prof... 3 weeks ago By Steve
	MMU Nextruder mod tension screws By Alienbliep 4 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	No scraping at all. I tightened the screws a littl... 3 weeks ago By James... Does your screws scrape the holes? I suggest tight... 3 weeks ago By Alien... I have the same problem. Did a few prints without ... 3 weeks ago By James... view all posts
	Print head strangely shifted right By YigalB 3 weeks ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	While printing this known duck, the head started p... 3 weeks ago By Yigal...