| |
Topic Title |
Forum |
 |
Unable To Inlay a Design Into a Surface By work n hard not hardly workin 2 days ago | Last Post: 2 days ago
|
PrusaSlicer |
| |
|
 |
Crash Detected By gb160 9 months ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
 |
Heatsink spacer missing, how to move forward? By Shasha 1 year ago | Last Post: 2 days ago
|
Assembly and first prints troubleshooting |
| |
|
 |
Aplikace Prusa By Vladimir 4 days ago | Last Post: 2 days ago
|
OpenPrintTag |
| |
|
 |
when adding MK3S+ and brand new install of Prusa link, get 404 not found from connect.prusa3d.com By Karlg100 2 days ago | Last Post: 2 days ago
|
Bugs & Errors |
| |
|
|
|
help me with printer setting By AWL_Prusa 3 days ago | Last Post: 2 days ago
|
Prusa CORE One L |
| |
|
 |
How much does the box with an MK4 kit weigh? By Tom Horsley 2 years ago | Last Post: 2 days ago
|
General discussion, announcements and releases |
| |
|
 |
Print Bed Loose? By Shorty54 3 days ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
|
|
First use and fail By quarkholon 3 days ago | Last Post: 2 days ago
|
Assembly and first prints troubleshooting |
| |
|
 |
Heatbed Assembly 4.27 Covering Heatbed Cables By jlok42 2 days ago | Last Post: 2 days ago
|
Assembly and first prints troubleshooting |
| |
|
 |
As of 6.4.0, the XL still crashes toolheads into one another. It is inexcusable. By ktastrophe 2 weeks ago | Last Post: 2 days ago
|
General discussion, announcements and releases |
| |
|
 |
General Maintenance By shrap 2 days ago | Last Post: 2 days ago
|
General discussion, announcements and releases |
| |
|
 |
Faster Prints (accidentally) By Old&Slow 2 days ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
 |
Core One LED light strips By bowtie6 5 months ago | Last Post: 2 days ago
|
User mods |
| |
|
 |
MK4S asks me to unload and load filament before the printing starts By Marteinn - 3DP Iceland 3 days ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
 |
Frage zu CoreOne+ Upgrade Teilesatz By khprotzer 3 days ago | Last Post: 2 days ago
|
Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
| |
|
 |
Printing TPU/TPE on Prusa XL By JtresslerIMEC 3 years ago | Last Post: 2 days ago
|
How do I print this? (Printing help) |
| |
|
|
|
Prusaslicer has encountered an error By klaus.g2 2 days ago | Last Post: 2 days ago
|
PrusaSlicer |
| |
|
 |
Poor Print Quality on Sloped Surfaces That Face the Rear By t5montecarlo 2 weeks ago | Last Post: 2 days ago
|
General discussion, announcements and releases |
| |
|
 |
Buddy Camera in the Core one reads the code and shows up in Connect, but is not registered. By Dik Harrison 5 months ago | Last Post: 2 days ago
|
General discussion, announcements and releases |
| |
|