| |
Topic Title |
Forum |
 |
Fehlermeldung: Filament wiederladen By Conbey 2 days ago | Last Post: 6 hours ago
|
Hilfe zur Hardware, Firmware und Software |
| |
|
 |
Core One ASA issues By derekradley 8 hours ago | Last Post: 8 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Possible ghosting issues after calibration By SocialMisanthrope 3 days ago | Last Post: 8 hours ago
|
Assembly and first prints troubleshooting |
| |
|
 |
scarfjoint enforcer modifier By 4Thee 2 weeks ago | Last Post: 9 hours ago
|
PrusaSlicer |
| |
|
 |
WiFi and Ethernet not working By Akentut 12 months ago | Last Post: 10 hours ago
|
Hardware, firmware and software help |
| |
|
 |
Wifi module not detected By Patrovite 3 months ago | Last Post: 10 hours ago
|
Hardware, firmware and software help |
| |
|
 |
Print Trouble shooting - Always second layer By SullySquatch 3 weeks ago | Last Post: 11 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Solidworks xDesign By Razor 7 days ago | Last Post: 11 hours ago
|
General discussion, announcements and releases |
| |
|
 |
MK4S/MMU3 How can I get into the Tool Mapping manually By chandler 4 days ago | Last Post: 12 hours ago
|
Hardware, firmware and software help |
| |
|
 |
After each power on, new Core One recalibrates home, bangs the Nextruder against the corner and reports a printer collision By Matthias Nagel 4 months ago | Last Post: 12 hours ago
|
Assembly and first prints troubleshooting |
| |
|
 |
Why is the quality of my nylon-cf prints getting progressively worse? By samfo 3 days ago | Last Post: 12 hours ago
|
How do I print this? (Printing help) |
| |
|
 |
Slicer doesn't connect By TurboResearch 12 hours ago | Last Post: 12 hours ago
|
PrusaSlicer |
| |
|
|
|
High speed for one color, low speed for others By Daniel Ezell 12 hours ago | Last Post: 12 hours ago
|
How do I print this? (Printing help) |
| |
|
|
|
Specify extruder for infill By Daniel Ezell 13 hours ago | Last Post: 13 hours ago
|
How do I print this? (Printing help) |
| |
|
 |
Print Bed Loose? By Shorty54 13 hours ago | Last Post: 13 hours ago
|
Hardware, firmware and software help |
| |
|
 |
Direct addressing of GPIO board By Denesius 4 days ago | Last Post: 13 hours ago
|
Prusa add-ons (GPIO, accelerometer,...) |
| |
|
|
|
MK4S ironing settings different than MK4? By coalesce714 17 hours ago | Last Post: 13 hours ago
|
How do I print this? (Printing help) |
| |
|
 |
Prusa MK3S+ not opening RPi Port By ETTItroff 13 hours ago | Last Post: 13 hours ago
|
Prusa Connect & PrusaLink |
| |
|
 |
first layer anomaly By simoneg 2 days ago | Last Post: 15 hours ago
|
Hardware, firmware and software help |
| |
|
 |
Under extrusion? at start of seam By Matt 2 weeks ago | Last Post: 15 hours ago
|
Hardware, firmware and software help |
| |
|