Recent Posts

Forums | Topics

Page 9 / 27 Prev Next

	Topic Title	Forum
	Any way to have an offline setup for the buddy3d camera? By BentiGorlich 5 months ago \| Last Post: 1 week ago	Hardware, firmware and software help
	Check out the Reddit link in this post:/p> Set up ... 1 week ago By antwe... My problem is, that in order to connect the camera... 4 months ago By Benti... There are no controls on the camera so you initial... 4 months ago By sabre... view all posts
	First Layer Calibration has Jagged edges By Fabiola Ar 1 week ago \| Last Post: 1 week ago	Assembly and first prints troubleshooting
	Thank you so much for the replies. I will try thes... 1 week ago By Fabio... Live z is way too high, read/p> 1 week ago By Rueba... Try giving the print sheet a really thorough clean... 1 week ago By Diem view all posts
	Very occasionally: no print whatsoever (SL1S) By Rob Meades 1 week ago \| Last Post: 1 week ago	Hardware, firmware and software help
	I've had this happen twice now with my SL1S (upgra... 1 week ago By Rob M...
	help with extrusion multipiler calibration By evolutio 1 week ago \| Last Post: 1 week ago	Assembly and first prints troubleshooting
	You can ignore the message "gcode cropped of lengt... 1 week ago By T.Mun... I tried with the Youtube video, but it always fail... 1 week ago By evolu... I use both methods. The wall method is accurate (c... 1 week ago By hyige... view all posts
	Extruder crashing on wipe tower after firmware update By Steve 1 week ago \| Last Post: 1 week ago	Hardware, firmware and software help
	I had something similar on my MK4S. I found that o... 1 week ago By Mr Sl... Extruder crashing into wipe tower after update I... 1 week ago By Steve
	Filament Change with MMU3 takes five minutes By barney15e 1 week ago \| Last Post: 1 week ago	Hardware, firmware and software help
	Normal wipe tower operation up until the point whe... 1 week ago By barne...
	Clicking noise coming from extruder unable to print By 37VI5 1 week ago \| Last Post: 1 week ago	Hardware, firmware and software help
	Clicking noise coming from extruder. This started ... 1 week ago By 37VI5
	For those getting the INDX are you getting the 4 head or 8 head? By hyiger 4 months ago \| Last Post: 1 week ago	General discussion, announcements and releases
	I am waiting on pricing to make my decision on the... 1 week ago By rjb22... Four. I think most multi material use cases are gi... 1 week ago By Spear... the only thing that gives me a used case for eight... 4 months ago By GBMar... view all posts
	6.5.3 Firmware for Prusa MK4 By Jan Kratochvíl 1 month ago \| Last Post: 1 week ago	General discussion, announcements and releases
	Looks like there is an open bug here:/p> 1 week ago By Count... This got me too. Hopefully Prusa corrects it soon 2 weeks ago By Count... Hi Is there an issue with this version reporting T... 2 weeks ago By rwill...
	Strongly considering this, but... By VulpineMac 1 week ago \| Last Post: 1 week ago	General discussion, announcements and releases
	Just to give you a search team, "Vorlong" (a Voron... 1 week ago By mnent... Unfortunately "design and build to order" is not p... 1 week ago By Jürge... Then Core One L will not suit your minimal require... 1 week ago By _Kasz...
	DNS fail, no DNS showing from DHCP? By SurprisingEdge 1 year ago \| Last Post: 1 week ago	Hardware, firmware and software help
	when I tried to set a static IP address on my MK4/... 1 week ago By Bytor Having the same issue where the Printer is getting... 1 week ago By Baile... I am really sorry to revive this post from last ye... 3 months ago By OcarC... view all posts
	Extruder crashing into wipe tower after update By Steve 1 week ago \| Last Post: 1 week ago	Hardware, firmware and software help
	I've just updated to the "new" firmware, and on my... 1 week ago By Steve
	Extruder crashing on wipe tower By Steve 1 week ago \| Last Post: 1 week ago	Hardware, firmware and software help
	I've just updated to the "new" firmware, and on my... 1 week ago By Steve
	Extruder crashing on wipe tower By Steve 1 week ago \| Last Post: 1 week ago	Hardware, firmware and software help
	I've just updated to the "new" firmware, and on my... 1 week ago By Steve
	First layer/Bad adhesion By MaxStey 2 weeks ago \| Last Post: 1 week ago	How do I print this? (Printing help)
	You can carefully and lightly sand the PEI layer o... 1 week ago By miros... You probably want both: Choose one regular cleani... 2 weeks ago By Diem Thanks, It helped, I'll check my isopropyl alcohol... 2 weeks ago By MaxSt... view all posts
	Spare MK4S build plates, can I use on Core One L? By JMERS 1 week ago \| Last Post: 1 week ago	General discussion, announcements and releases
	You could maybe create a Core One L print profile ... 1 week ago By hyige... For some small nodels that might work but you woul... 1 week ago By _Kasz... I am considering a Core One L and have MK4S with e... 1 week ago By JMERS
	Printables and suspicious files By Same Old Shane 1 week ago \| Last Post: 1 week ago	General discussion, announcements and releases
	And wouldn't that be enough to start with a quick ... 1 week ago By miros... Things seem better. Though I am still pretty sure ... 1 week ago By shrap thanks for the efforts, it really is a plague thes... 1 week ago By h3li0 view all posts
	Online Chat disappeared? By pink_clown 1 week ago \| Last Post: 1 week ago	General discussion, announcements and releases
	same here, tried three different browsers, cleared... 1 week ago By spice... clear your cache 1 week ago By Rueba... When clicking on On line Chat button, nothing happ... 1 week ago By pink_...
	PrusaSlicer With Automatic Bed Mesh Visualization By hyiger 2 weeks ago \| Last Post: 1 week ago	PrusaSlicer
	A very nice tool! v1.3.0 works as expected on the ... 1 week ago By ssmit... Nice 👍👍 i will test it again. 1 week ago By jan.d... New version 1.3.0 available here:/p> What's new ... 1 week ago By hyige... view all posts
	6.5.3 firmware seems really broken By david.s174 4 weeks ago \| Last Post: 1 week ago	Hardware, firmware and software help
	Mike B: I haven't noticed it jerking along the x-... 1 week ago By Ricks... These two issues have been raised with the firmwar... 1 week ago By Mike ... This I think I am seeing as well, but both on the ... 1 week ago By Mike ... view all posts