Recent Posts

Forums | Topics

Page 21 / 25 Prev Next

	Topic Title	Forum
	Issues with MMU3 Spool holders By 3dprintingbeast 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I have been struggling with my MMU3's spool roller... 3 weeks ago By 3dpri...
	change 0.4HF to 0.6HF By Hondzik 1 month ago \| Last Post: 3 weeks ago	How do I print this? (Printing help)
	Since you really haven't described the problem bey... 3 weeks ago By hyige... I just wanted to know if anybody else have same pr... 3 weeks ago By Hondz... Need a lot more information. Did you also reslice ... 4 weeks ago By hyige...
	Printer is vibrating terribly By simmania 2 months ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	Yeah, I never noticed a difference in print qualit... 3 weeks ago By GBMar... The H2X is equivalent to the Core One with the Hul... 4 weeks ago By hyige... While it is normal, I always felt the Core One sha... 4 weeks ago By iftib... view all posts
	[Projekt] Eigenes Prusa Touch UI – alles läuft, außer Temperatursteuerung über PrusaLink 😅 By Damaskus89 3 weeks ago \| Last Post: 3 weeks ago	Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, …
	Hi zusammen, ich bastle aktuell an einer eigenen... 3 weeks ago By Damas...
	Strange IP address By JM 3 weeks ago \| Last Post: 3 weeks ago	PrusaSlicer
	Thankyou both for your help (I did try 'who is' bu... 3 weeks ago By JM Of runto get ibfi what IP address your connections... 3 weeks ago By _Kasz... RE: Strange IP address 3 weeks ago By GertL view all posts
	Core One + Continuous issues By Crazy 1 month ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	I have almost constant crashes/restarts. Had one t... 3 weeks ago By Ron S Not had one issue with my Core One's so I suspect ... 3 weeks ago By kjgou... I have a recently assembled C1+ and not had any su... 1 month ago By James... view all posts
	Any way to have an offline setup for the buddy3d camera? By BentiGorlich 5 months ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	Check out the Reddit link in this post:/p> Set up ... 3 weeks ago By antwe... My problem is, that in order to connect the camera... 5 months ago By Benti... There are no controls on the camera so you initial... 5 months ago By sabre... view all posts
	First Layer Calibration has Jagged edges By Fabiola Ar 4 weeks ago \| Last Post: 3 weeks ago	Assembly and first prints troubleshooting
	Thank you so much for the replies. I will try thes... 3 weeks ago By Fabio... Live z is way too high, read/p> 3 weeks ago By Rueba... Try giving the print sheet a really thorough clean... 3 weeks ago By Diem view all posts
	Very occasionally: no print whatsoever (SL1S) By Rob Meades 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I've had this happen twice now with my SL1S (upgra... 3 weeks ago By Rob M...
	help with extrusion multipiler calibration By evolutio 4 weeks ago \| Last Post: 3 weeks ago	Assembly and first prints troubleshooting
	You can ignore the message "gcode cropped of lengt... 3 weeks ago By T.Mun... I tried with the Youtube video, but it always fail... 3 weeks ago By evolu... I use both methods. The wall method is accurate (c... 3 weeks ago By hyige... view all posts
	Extruder crashing on wipe tower after firmware update By Steve 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I had something similar on my MK4S. I found that o... 3 weeks ago By Mr Sl... Extruder crashing into wipe tower after update I... 3 weeks ago By Steve
	Filament Change with MMU3 takes five minutes By barney15e 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	Normal wipe tower operation up until the point whe... 3 weeks ago By barne...
	Clicking noise coming from extruder unable to print By 37VI5 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	Clicking noise coming from extruder. This started ... 3 weeks ago By 37VI5
	Strongly considering this, but... By VulpineMac 3 weeks ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	Just to give you a search team, "Vorlong" (a Voron... 3 weeks ago By mnent... Unfortunately "design and build to order" is not p... 3 weeks ago By Jürge... Then Core One L will not suit your minimal require... 3 weeks ago By _Kasz...
	DNS fail, no DNS showing from DHCP? By SurprisingEdge 1 year ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	when I tried to set a static IP address on my MK4/... 3 weeks ago By Bytor Having the same issue where the Printer is getting... 3 weeks ago By Baile... I am really sorry to revive this post from last ye... 3 months ago By OcarC... view all posts
	Extruder crashing into wipe tower after update By Steve 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I've just updated to the "new" firmware, and on my... 3 weeks ago By Steve
	Extruder crashing on wipe tower By Steve 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I've just updated to the "new" firmware, and on my... 3 weeks ago By Steve
	Extruder crashing on wipe tower By Steve 3 weeks ago \| Last Post: 3 weeks ago	Hardware, firmware and software help
	I've just updated to the "new" firmware, and on my... 3 weeks ago By Steve
	First layer/Bad adhesion By MaxStey 1 month ago \| Last Post: 3 weeks ago	How do I print this? (Printing help)
	You can carefully and lightly sand the PEI layer o... 3 weeks ago By miros... You probably want both: Choose one regular cleani... 1 month ago By Diem Thanks, It helped, I'll check my isopropyl alcohol... 1 month ago By MaxSt... view all posts
	Spare MK4S build plates, can I use on Core One L? By JMERS 4 weeks ago \| Last Post: 3 weeks ago	General discussion, announcements and releases
	You could maybe create a Core One L print profile ... 3 weeks ago By hyige... For some small nodels that might work but you woul... 4 weeks ago By _Kasz... I am considering a Core One L and have MK4S with e... 4 weeks ago By JMERS