Notifications
Clear all

Mitigate wall bulge  

Page 4 / 7
  RSS
rinkel
(@rinkel)
Estimable Member
RE: Mitigate wall bulge

Ok, since you never can have enough nozzle boxes, i printed one more.

Before "Detect Thin Walls"

After "Detect Thin Walls"

Publié : 28/06/2022 7:03 pm
BitForge a aimé
Erik
 Erik
(@erik-3)
Estimable Member
Topic starter answered:
RE: Mitigate wall bulge

Is the inside of the box also dimensionally correct?

Publié : 28/06/2022 7:35 pm
BitForge a aimé
BitForge
(@bitforge)
Active Member
RE: Mitigate wall bulge

Interestingly,  I still get the bulge regardless of that setting. 

Publié : 28/06/2022 7:35 pm
rinkel
(@rinkel)
Estimable Member
RE: Mitigate wall bulge

For the Nozzle Box i do not know, since i don't know what the dimensions should be. But the nozzles fit nicely.

I will measure my own test-box to see if it's correct. 
I just threw away all my test objects.

Publié : 28/06/2022 8:03 pm
rinkel
(@rinkel)
Estimable Member
RE: Mitigate wall bulge

I think the accuracy is pretty good. It's actually dead-on. The caliper stretched a little when i put it on the desk.

Publié : 28/06/2022 8:08 pm
Erik
 Erik
(@erik-3)
Estimable Member
Topic starter answered:
RE: Mitigate wall bulge

All this time... All of the terrible looking prints...

Publié : 28/06/2022 8:09 pm
rinkel
(@rinkel)
Estimable Member
RE:

This seems to solve the issue for me, for now.
Unfortunately this is not a magic option that solves everything. There are cases where this option needs to be turned off. There are some issues on github to be found.

I remember that i had turned it on, but had unwanted side effects, that's why i have turned it off by default in my profiles. But i cannot remember why.

In another topic on github someone advised to turn this option off.
I reacted with this:

I posted a bug today (wall bulging) where turning this option on resolves it mostly.The problem is that sometimes this "Detect Thin Walls" should be turned on, and for other issues, like this, it should be turned off again.It's like the magic "restart your computer" button to see if it solves your issue.

Publié : 28/06/2022 8:19 pm
Brad
 Brad
(@brad-2)
Trusted Member
RE: Mitigate wall bulge

"Detect thin walls" slightly improved the bulge but broke the smaller items of text on my model.

Posted by: @brad-2

I tried copying some of the other default Cura settings to Prusa Slicer, sliced and printed the model again but the bulge is back. Will try "Detect Thin Walls" and print again...

 

Publié : 28/06/2022 9:17 pm
rinkel
(@rinkel)
Estimable Member
RE:

Yeah, there you have issues on the opposite sides of this option. It solves one, but introduces another, precisely what i was affraid of. So eventhough it solved my issue for now, it probably will not in one of my future projects. That's why this issue needs to be solved in the software.

@Brad:
Have you tried Cura with this project?

 

Publié : 28/06/2022 9:25 pm
Brad
 Brad
(@brad-2)
Trusted Member
RE: Mitigate wall bulge

Yes my model was bulge-free when I tried it in Cura. It otherwise looked terrible with Cura's default settings though.

Posted by: @rinkel

@Brad:
Have you tried Cura with this project?

 

 

Publié : 28/06/2022 9:28 pm
rinkel
(@rinkel)
Estimable Member
RE: Mitigate wall bulge

Same here.

I won't get my hopes up too much, i saw many unresolved cases with the tag "Gap fill" on Github. There are now 2146 unresolved issues, 75 of them are "Gap fill" and 8 issues resolved.

Publié : 28/06/2022 9:37 pm
jsw
 jsw
(@jsw)
Famed Member
RE: Mitigate wall bulge

I would think, since they have a very good elephant's foot compensation in PS, that it would be possible to develop a similar scheme to compensate for various bulge ('buldge' 🙂 ) situations, in particular in the case of a bulge surrounding a solid level in a print.

Some time ago I remember a case of a Benchy, printed in ABS, which had a similar issue.  Another user remarked about it and I volunteered, since I had a spool of the exact same filament loaded, to do a sanity check and print one myself.  Just as the other user experienced, I got a bulge at the same point, where the solid deck attached to the hull.

I would think that analysis could be done on the model during the slicing process, which would identify possible trouble spots, and then compensate, shrinking the dimensions of the affected layers slightly, in a manner similar to what is done on the lowest layers for elephant foot compensation.

Publié : 28/06/2022 10:45 pm
jsw
 jsw
(@jsw)
Famed Member
RE: Mitigate wall bulge

Out of curiosity, and mainly for sh*ts and grins, I downloaded that nozzle box, even though I don't have nearly enough nozzles to need a box.  😉

I was curious how the two slicers (PS, Cura) would differ and which tweaks in the configs might make the bulge (buldge?) less obvious.

I really saw no obvious bul(d)ge, and little if any difference between PrusaSlicer (left) and Cura (center).

The one on the right was due to the fact that the last time I sliced something for the Prusa using Cura, I apparently had 'fuzzy skin' checked and did not notice it until the print was mostly finished.

) at least less obvious.

 

Publié : 29/06/2022 1:06 am
rinkel
(@rinkel)
Estimable Member
RE: Mitigate wall bulge

But the benchy hull line is a very common thing and no slicer has been able to solve it automatically. Prusa did a whole topic about this.

Did you print it with the "Detect thin walls" on or off?

Publié : 29/06/2022 7:23 am
jsw
 jsw
(@jsw)
Famed Member
RE: Mitigate wall bulge

With the MK3S I have, and with a Taz-5 at our local makerspace, using PLA filament, the Benchy will print with not enough bulge at the deck level to notice if you are not specifically looking for it.

With ABS, it does show up very obviously.

Publié : 29/06/2022 11:19 am
rinkel
(@rinkel)
Estimable Member
RE: Mitigate wall bulge

This issue is also reported awhile ago on Github:  #7973

Publié : 29/06/2022 12:09 pm
rinkel
(@rinkel)
Estimable Member
RE: Mitigate wall bulge

Interesting:

Lets give it a try!

Publié : 29/06/2022 12:46 pm
SujetRandom
(@sujetrandom)
Active Member
RE: Mitigate wall bulge

WTF ? perimeter generator ? where ? i don't have this feature ???

Publié : 29/06/2022 12:59 pm
rinkel
(@rinkel)
Estimable Member
RE: Mitigate wall bulge

It's in the new version: 2.5.0 alpha 2
You can download it from github.
Like i said in my previous post, this issue was already reported a few times in the past, and it seems they have fixed it in collaboration with Cura.

Printing right now, without the "Detect thin walls" option.

Posted by: @sujetrandom

WTF ? perimeter generator ? where ? i don't have this feature ???

 

Publié : 29/06/2022 1:03 pm
SujetRandom a aimé
rinkel
(@rinkel)
Estimable Member
RE: Mitigate wall bulge

And here we go....

I printed my test-box again (i guess i finally have enough nozzleboxes.. or maybe i need one more...)
without the "detect thin walls" option

Tadaa...
It's working!

Another thing they've done is creating a better seam. Much better now.

Publié : 29/06/2022 1:13 pm
Page 4 / 7
Partager :