English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ User mods - OctoPrint, enclosures, nozzles, ... Notifications Clear all User mods - OctoPrint, enclosures, nozzles, ... | RSS Page 32 / 64 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Next Topic Title Last Post Views Posts Author Rasberry Pi 4 By Andi G. on Nov 25, 20 2951 10 Wes 32bit mb (on mk3s?) By Neophyl on Nov 24, 20 5709 4 admpc Modded hot end mounting parts to conteract Pin... By cwbullet on Nov 22, 20 1649 2 useruser55 PRUSA i3 MK3S ENCLOSURE- PSU wires to short By Flood on Nov 20, 20 1634 2 Joseph Fan-Powered or Motor-Powered LED for Nozzle By Flood on Nov 20, 20 1425 1 Flood pi0W 2 power supply sources. By DutchOrange on Nov 19, 20 1293 1 DutchOrange Is BNBSX or Bondtech Extruder a worthwhile upg... By Jeansburger on Nov 18, 20 1886 3 Jeansburger Upgrading Hotend Parts By -- on Nov 16, 20 2389 4 Fargo Raspberry Pi 400 By Clemens M. on Nov 16, 20 5947 16 Duncan Blackw... Ordered Bear upgrade! By odingalt on Nov 16, 20 9584 30 matthew.m63 Which Raspberry is needed on a MK3S for octopr... By HotWiL on Nov 15, 20 5574 40 HotWiL mesh bed leveling during pre-heat By -- on Nov 15, 20 2224 3 Chip Is PrusaMeshMap still a valid plugin? By Baklin on Nov 15, 20 1605 2 AWilling Good max temp for an enclosure? By Gorgele on Nov 13, 20 20601 10 Nicoli Selenium webdriver returns empty list from fin... By ginarivera1974 on Nov 13, 20 1155 1 ginarivera197... Move filament run out sensor higher? By Rlowery95 on Nov 10, 20 1701 3 Dan Silent part fan upgrade for Mk2, Mk3 By nacalco on Nov 04, 20 2177 2 dangerousdoug Thekkiinngg Powder Coated PEI sheet V4 - Impre... By cwbullet on Nov 03, 20 4871 18 lpopesco Parts to link filament dryer to a modificated ... By Flo4Print on Oct 31, 20 2435 1 Flo4Print First time changing a nozzle, will I need to c... Answered By bobstro on Oct 31, 20 3944 8 kirby Page 32 / 64 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Next Share: