English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ User mods - OctoPrint, enclosures, nozzles, ... Notifications Clear all User mods - OctoPrint, enclosures, nozzles, ... | RSS Strona 22 / 65 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 Następny Tytuł Tematu Ostatni Post Widok Posty Author UPS on the printer --- didn't work?! Przez MysDawg on Dec 19, 21 3844 9 Mirar Killing Power through Smart Plug instead of on... Przez MysDawg on Dec 18, 21 7150 11 123Dprint! Water Cooling the hot end Przez Yazzman56 on Dec 18, 21 4411 3 DXM Bearly a MK3S Przez ktm1090 on Dec 15, 21 1973 1 ktm1090 LED STRIP 5050 via GPIO RGB Controller Przez ebarnes on Dec 15, 21 2057 1 ebarnes Problem with first layer calibration and z-hig... Przez Beny44 on Dec 10, 21 2935 15 crusaderxs Profile for a 0.3 mm nozzle Answered Przez DigTech on Dec 05, 21 14224 54 Frippe75 At what temp will the parts around the nozzle ... Przez muo on Dec 05, 21 2367 4 muo Bondtech LGX/Mosquito Kit really slow extruiso... Przez Kittehn on Dec 02, 21 1954 4 Kittehn Working (Octopi) Image needed for Rapsberry Pi... Przez Diem on Dec 02, 21 1554 6 Austria777 How to make use of Mosquito Magnum Przez apemberton on Dec 01, 21 6871 9 DustinJay Which Hardware for Octoprint, Camera, Fan Cont... Przez FoxRun3D on Nov 30, 21 2787 7 Robin Why you shouldn't use gcode from Prusaprinters Przez jsw on Nov 28, 21 2913 6 Thomas Looking for a y-splitter for the hot-end-fan f... Przez Dan Rogers on Nov 24, 21 2111 4 Andrew Biss Power cable Przez Dan Rogers on Nov 23, 21 2674 5 Ducker31 My MKS3 Enclosure Przez jsw on Nov 21, 21 2180 4 ScottM I've been searching but need assistance!!! Und... Przez jsw on Nov 18, 21 3733 9 SubseaUK Under-extrusion and TMC drive overtemp Answered Przez PALM on Nov 14, 21 2178 4 PALM Hemera Upgrade but getting calibration failure... Przez Kuroi Kenjin on Nov 13, 21 2429 5 Kuroi Kenjin Glossy surface Przez AnnieR on Nov 13, 21 2746 7 MSchwarz Strona 22 / 65 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 Następny Share: