English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 1 / 187 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 Następny Tytuł Tematu Ostatni Post Widok Posty Author e-TPU esun 95A settings Przez Tut on 4 days temu 14105 18 yoola Wavy lines / ripples in top layer Przez DByte on 5 days temu 33006 52 xavierx Elephant foot? Nozzle cleaning? Przez Eule on 6 days temu 379 7 Eule Fuzzy Skin - First Fuzzy Skin layers will not ... Przez Bart on 6 days temu 139 1 Bart Bad "lines" when print almost horizontal surfa... Przez Peter on Dec 19 198 6 Peter ESUN PETG Print Settings Answered Przez Constantin on Dec 18 10637 32 Rocky79 Printing 250mm wide - A toolpath outside the p... Przez Brad on Dec 17 7753 13 PorrdigeFacto... What Settings Should I Be Looking At? Przez parallon on Dec 17 414 7 parallon Can I print multiple colors at the same layer? Przez Tiago Carvalho on Dec 16 27253 19 0mib How do I print each layer in same infill direc... Przez ufanders on Dec 16 20394 21 Bvdv Moving the nozzle wipe Przez dflipse on Dec 15 4763 9 DrAl Bulge when print reaches "solid" lay... Przez KielTheLegend on Dec 15 306200 529 Nicolai Flat spots/bad finish separation on supported ... Przez Evan Judson on Dec 13 521 3 Evan Judson Gaps on top layer of print Przez Brian on Dec 13 886 3 mgantner How to improve overhangs on this print? Przez Diem on Dec 12 371 2 Maciej Latuse... How to print small PLA patterns on glass? Przez Charles on Dec 11 341 1 Charles Having cyclic underextrusion. Suspect bontech ... Przez RedDawg on Dec 09 478 4 RedDawg how do i stop curling Przez Friedham on Dec 08 19544 25 Cowen Blob of filament extruded when resuming from a... Przez Daniel Siffred... on Dec 07 7134 13 RichardLarson Peeling off outlines Przez MaiBo on Dec 07 453 2 MaiBo Strona 1 / 187 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 Następny Share: