English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 83 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author Please analyze print quality Przez Swiss_Cheese on May 15, 21 3783 6 Astroxss TPE print problems Przez Swiss_Cheese on May 13, 21 4411 16 DeltaWerks Need advice on troubleshooting my Benchy Przez MightWorks on May 13, 21 4339 9 MightWorks Problems printing with PETG first layer. Przez -- on May 13, 21 5231 15 Steve Gluing Help Przez -- on May 12, 21 3660 9 Big Buddha Benchy printing problem with PETG Przez Jimbo70 on May 12, 21 3445 6 Jimbo70 Printing with Prusa ABS-T Przez cwbullet on May 12, 21 3335 4 shay.s 1st layer issue? Przez Bob the Maker on May 12, 21 2295 4 Bob the Maker Corner warp/lifting Przez cwbullet on May 11, 21 5984 5 Jerry S Weird noise and print failing at same spot Przez dakiki on May 11, 21 2829 10 dakiki Brand New Official Hot End, Now Overhangs are ... Przez cwbullet on May 10, 21 3168 16 TwoBallScrewB... Damaged in bottom printing Przez -- on May 10, 21 2309 3 liubie Will printing nylon destroy my powder coated s... Przez arjan on May 09, 21 18575 20 Tellblom How to avoid these hollow lines (underextrusio... Przez -- on May 09, 21 11041 37 flux_capacito... Problem with ColorFabb PLA / PHA Filaments Przez SteveM on May 08, 21 3791 6 Rob PETG retraction settings Przez FoxRun3D on May 08, 21 13458 4 der_da PETG Stringing and broke my prusaprinter Przez cwbullet on May 08, 21 3115 9 offiRent Print quality issue on first layer smal areas Przez -- on May 07, 21 3149 16 D.Ebi PLA vendor, model or slicer issue? Przez Leigh213 on May 07, 21 2714 19 Leigh213 First layer issue Przez ssill2 on May 06, 21 6017 27 dakiki Strona 83 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: