English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 5 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Bad "lines" when print almost horizontal surfa... Da Peter on Dec 19 2204 6 Peter ESUN PETG Print Settings Answered Da Constantin on Dec 18 14600 32 Rocky79 Printing 250mm wide - A toolpath outside the p... Da Brad on Dec 17 9324 13 PorrdigeFacto... What Settings Should I Be Looking At? Da parallon on Dec 17 1698 7 parallon Can I print multiple colors at the same layer? Da Tiago Carvalho on Dec 16 33223 19 0mib How do I print each layer in same infill direc... Da ufanders on Dec 16 25268 21 Bvdv Moving the nozzle wipe Da dflipse on Dec 15 7181 9 DrAl Flat spots/bad finish separation on supported ... Da Evan Judson on Dec 13 1030 3 Evan Judson Gaps on top layer of print Da Brian on Dec 13 1486 3 mgantner How to improve overhangs on this print? Da Diem on Dec 12 2329 2 Maciej Latuse... Having cyclic underextrusion. Suspect bontech ... Da RedDawg on Dec 09 1610 4 RedDawg how do i stop curling Da Friedham on Dec 08 23847 25 Cowen Blob of filament extruded when resuming from a... Da Daniel Siffred... on Dec 07 9673 13 RichardLarson Peeling off outlines Da MaiBo on Dec 07 1392 2 MaiBo Support Material For Openings on Part Da Yngeinstn on Dec 05 1222 5 Yngeinstn Under extrusion after seam Da jake181 on Dec 05 1419 1 jake181 0.8 Nozzle - over or under extrusion? Da eleph67 on Dec 03 887 2 Basic HELP Da Robin on Dec 02 938 2 alvaroachu Corner Bubbling and Rough Da Friso Modderma... on Dec 01 2499 4 stokes776 Threads Da alvaroachu on Nov 29 917 4 alvaroachu Pagina 5 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: