English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Stránka 29 / 190 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Flame-Retardant Capabilities Od Stefan on Mar 28, 23 2312 2 BParr4 Issue printing simple 3 part design Od FoxRun3D on Mar 27, 23 1957 2 Chris Print speed by layer Answered Od addohm on Mar 27, 23 4344 10 addohm Printing hoverangs in a corkscrew conveyor Od Galinette on Mar 25, 23 2011 1 Galinette Reducing staircase effect without lowering the... Od Galinette on Mar 24, 23 1935 1 Galinette Issue with rough top infill edges on 0.6mm noz... Od Mark Hähnel on Mar 22, 23 1733 1 Mark Hähnel Issues printing TPU Od ssill2 on Mar 20, 23 9750 14 Slayer Looks good, prints bad Od Rajah on Mar 20, 23 2203 5 Rajah Flat areas not consistent Od Diem on Mar 20, 23 2261 4 CupCap Vase Mode - Unexpected Nozzle Movement Answered Od broconne on Mar 19, 23 1692 4 broconne Print Wont stick to bed? curling sometimes Od jsw on Mar 19, 23 3100 7 cin05bus First layer suddenly stops sticking Answered Od zukpr on Mar 18, 23 4813 5 zukpr Black mark on prints Od viesturs on Mar 18, 23 18074 14 Phil Printing With NylonX Od Ridni Photo on Mar 17, 23 13131 20 alejo.v2 Print "block" Od Berne on Mar 17, 23 2626 9 Berne How to print the bottom layer optically as eve... Od Armin on Mar 15, 23 2092 1 Armin Weird printing problem...new to this Od Neophyl on Mar 14, 23 1898 4 randito70030 Large Print Not Sticking (Curling) on corners Od jsw on Mar 13, 23 5118 5 Scott Prusament Galaxy Black delamination Od Dirt-e on Mar 13, 23 5901 4 Mike01Hu Petg Print Strining Od Diem on Mar 12, 23 2420 5 XReptor Stránka 29 / 190 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Další Share: