English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 182 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author 0.25, 0.3 and 0.4mm layer heigh for 0.6mm nozz... Przez bobstro on Jul 13, 18 12056 2 luczjanoo Prusa MK3 Printing at .3 layer Przez marco.r4 on Jul 12, 18 1751 3 marco.r4 ABS printing issus.. Przez Peter L on Jul 12, 18 774 2 Dad Workshop Multi part printing with different print setti... Przez arto.h on Jul 11, 18 2343 3 arto.h How can I fix this ? Przez JoanTabb on Jul 11, 18 2153 5 nubin.s Why is this print failing? Przez alejo.v2 on Jul 10, 18 2507 13 paul.a13 Weak infill or under extrusion issue after cha... Przez thrawn86 on Jul 10, 18 1840 2 Factao Effel tower settings Przez thrawn86 on Jul 10, 18 2114 2 robert.r32 Calibration issue? Przez P. Larsen on Jul 09, 18 1438 3 P. Larsen Struggling to fine-tune print quality Przez bobstro on Jul 08, 18 6932 13 peter.k40 Multicolor with one nozzle but in selected are... Przez Jerry on Jul 08, 18 1951 6 rocendroll Why is the bottom different than the top? Przez stoofer on Jul 07, 18 3296 6 mulder Porblems with orange petg Przez themzlab on Jul 05, 18 1752 2 roland.f1 Difficult print orientation Przez Asraff Amzani on Jul 05, 18 2328 9 Maj Support Improvement Przez arjan.s2 on Jul 05, 18 1797 3 arjan.s2 What happened while printing this benchy? Przez Factao on Jul 04, 18 2543 3 Factao Print part deformation Przez Asraff Amzani on Jul 04, 18 1630 2 Aitwar Printing Below 190°C Przez Martin Wolfe on Jul 03, 18 2831 10 Martin Wolfe Gaps when printing round things Przez Sam on Jul 03, 18 3204 3 Sam PETG on textured coated sheet Przez bobstro on Jul 03, 18 3818 5 Eikonic Strona 182 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: