English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Page 151 / 190 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Suivant Titre du sujet Dernier message Nombre de vues Messages Author XYZ calibration cube Par MasterHead on Jun 27, 19 6247 2 makern3rd Excess of the filaments Par bobstro on Jun 26, 19 1629 3 Claudio Gallo Printing problem Par Peter M on Jun 26, 19 2341 12 Ratthy How Print with PVA Support Material without Mu... Par toaf on Jun 26, 19 1926 4 burcu bora.a Weird Rough Surface on Overhang Par -- on Jun 25, 19 3306 8 davep Stringing Par MasterHead on Jun 25, 19 2350 11 MasterHead Change Filament Settings Par Asurp on Jun 25, 19 10698 5 Asurp How would you print this? Material and support... Par -- on Jun 24, 19 2228 8 rainer.m Any thoughts about this broken prints? Answered Par Peter M on Jun 24, 19 2971 15 Roichu How do I set an auto pause during print to cha... Par RH_Dreambox on Jun 21, 19 5540 6 Jake Best way to post process clear pla Answered Par Peter M on Jun 21, 19 3363 6 GBbiker ABS+ tips - is this too hot? Par Nikolai on Jun 20, 19 16585 4 THiNK rc STL file exported from blender 2.8 is not reco... Answered Par Victor S on Jun 19, 19 4287 3 Victor S Skipping layers or under extrusion for an enti... Par -- on Jun 19, 19 2974 4 Technolio PETG weaker than PLA. Answered Par Short'n'quick on Jun 18, 19 15356 14 Short'n'quick problems with printing Par -- on Jun 17, 19 1753 2 carlos Weird consistent layer shifting Par -- on Jun 17, 19 3385 10 LoaderB0T Perimeters do not connect Par Antalies on Jun 17, 19 5102 5 Antalies Retraction, or nozzle temp, or what? Par bobstro on Jun 17, 19 4981 2 Wojomojo Small printing marks from retraction Par -- on Jun 16, 19 2049 2 peterferreira... Page 151 / 190 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Suivant Partager :