English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Avisos Vaciar todo How do I print this? (Printing help) | RSS Página 151 / 190 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Jams on MK3 , No Jam on MK3S Por Sink on Jun 30, 19 2386 9 Sink Adjusting settings for warping of PLA. Por Peter M on Jun 30, 19 8968 5 Zakalawe Layer Jumped Mid-print, Printer Pausing to Reh... Por Bunny Science on Jun 27, 19 2716 6 jcos Elephant foot like effect on top layers of pri... Por scott.b47 on Jun 27, 19 7522 4 scott.b47 XYZ calibration cube Por MasterHead on Jun 27, 19 6393 2 makern3rd Excess of the filaments Por bobstro on Jun 26, 19 1709 3 Claudio Gallo Printing problem Por Peter M on Jun 26, 19 2464 12 Ratthy How Print with PVA Support Material without Mu... Por toaf on Jun 26, 19 2018 4 burcu bora.a Weird Rough Surface on Overhang Por -- on Jun 25, 19 3413 8 davep Stringing Por MasterHead on Jun 25, 19 2464 11 MasterHead Change Filament Settings Por Asurp on Jun 25, 19 10979 5 Asurp How would you print this? Material and support... Por -- on Jun 24, 19 2325 8 rainer.m Any thoughts about this broken prints? Answered Por Peter M on Jun 24, 19 3057 15 Roichu How do I set an auto pause during print to cha... Por RH_Dreambox on Jun 21, 19 5851 6 Jake Best way to post process clear pla Answered Por Peter M on Jun 21, 19 3503 6 GBbiker ABS+ tips - is this too hot? Por Nikolai on Jun 20, 19 16941 4 THiNK rc STL file exported from blender 2.8 is not reco... Answered Por Victor S on Jun 19, 19 4432 3 Victor S Skipping layers or under extrusion for an enti... Por -- on Jun 19, 19 3089 4 Technolio PETG weaker than PLA. Answered Por Short'n'quick on Jun 18, 19 15711 14 Short'n'quick problems with printing Por -- on Jun 17, 19 1862 2 carlos Página 151 / 190 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Siguiente Compartir: