English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Avisos Vaciar todo How do I print this? (Printing help) | RSS Página 138 / 190 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Advice? Por 3DLibrarian on Dec 14, 19 1953 2 3DLibrarian Print failure Por Ken G. on Dec 14, 19 2845 12 Komet_82 ASA bridge woes Por hawai on Dec 14, 19 2376 1 hawai Baby Yoda won't finish correctly Por Frank_The_Rock on Dec 13, 19 1919 1 Frank_The_Roc... Line in Print (not line"s") Por lucatz70 on Dec 13, 19 2545 7 lucatz70 How do I make these prints better? Por Nikolai on Dec 12, 19 3314 4 Nater Problem Modeling PTFE Fitting Thread Por JoanTabb on Dec 12, 19 2473 2 Smiledemons Prints wont stick to front right corner only Por Frank Deschner on Dec 11, 19 11339 13 BootsInShoes Printing PCBs with a 3D printer Por towlerg on Dec 11, 19 3815 9 Lvet support problem help ! Por -- on Dec 10, 19 2364 4 Ian baskan Filament stuck between gears - copperFill Answered Por mikevrpv on Dec 10, 19 2984 7 mikevrpv Help with warping on lithophanes Por Jon on Dec 10, 19 5654 6 Jon Printing this house section is causing spaghet... Por doot doot beep on Dec 09, 19 2675 3 doot doot bee... Nylon vs. PETG Por Volker Jaenisc... on Dec 08, 19 23622 4 Volker Jaenis... Bridge not sticking, loops of bridge falling d... Por Anachronist on Dec 08, 19 25428 23 Anachronist Stringing problems with PETG Por Chuck on Dec 08, 19 2866 1 Chuck Had my first go at TPU...... Por Alpha on Dec 07, 19 1451 1 Alpha Blocked filament in printing head Por aka on Dec 07, 19 1754 1 aka How do I print something like this? Answered Por dwisejr on Dec 07, 19 3091 15 dwisejr change the filament Por crlinck on Dec 06, 19 2541 3 crlinck Página 138 / 190 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Siguiente Compartir: