English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 138 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Filament stuck between gears - copperFill Answered Da mikevrpv on Dec 10, 19 2781 7 mikevrpv Help with warping on lithophanes Da Jon on Dec 10, 19 5370 6 Jon Printing this house section is causing spaghet... Da doot doot beep on Dec 09, 19 2508 3 doot doot bee... Nylon vs. PETG Da Volker Jaenisc... on Dec 08, 19 21871 4 Volker Jaenis... Bridge not sticking, loops of bridge falling d... Da Anachronist on Dec 08, 19 23425 23 Anachronist Stringing problems with PETG Da Chuck on Dec 08, 19 2672 1 Chuck Had my first go at TPU...... Da Alpha on Dec 07, 19 1292 1 Alpha Blocked filament in printing head Da aka on Dec 07, 19 1602 1 aka How do I print something like this? Answered Da dwisejr on Dec 07, 19 2896 15 dwisejr change the filament Da crlinck on Dec 06, 19 2347 3 crlinck IR Sensor sensitivity on I3MKS3 MMU3S Da Volker Jaenisc... on Dec 06, 19 2529 1 Volker Jaenis... Clear Filament loads to nozzle but then endles... Da Zoltan on Dec 04, 19 2527 7 Fieniks Printing a battery holder Da Zoltan on Dec 04, 19 2731 7 fbjr G2 or G3 command line help Da Lichtjaeger on Dec 02, 19 2609 5 GBW Printing issues after few good prints Da GBW on Dec 02, 19 1761 4 Dráček Making a 3D Print File Da MikoRoG on Dec 02, 19 4530 6 MikoRoG Gitterroste drucken Da JoanTabb on Dec 01, 19 2922 14 Maxxuwe Prusament ASA and others Da huskyte on Dec 01, 19 1882 1 huskyte Sudden issues with clogged extruder. Da Rams on Nov 30, 19 4775 3 jpb123 How to setup a colorchange at a specific layer... Da Rams on Nov 30, 19 1850 3 Rams Pagina 138 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: