English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 126 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Are these vertical artifacts? Da Joey on Apr 20, 20 1444 1 Joey Stringing after blob Da Peter M on Apr 20, 20 2427 4 mKorniK Beginner teach/advise: if design OK, and slice... Da davidhajjar on Apr 19, 20 3595 7 davidhajjar Lithophane keeps skipping layers Da Peter M on Apr 19, 20 2901 5 MrCalm Prusa print farm settings Da islander2013 on Apr 18, 20 2182 2 islander2013 Frosch haftet nicht Da Tjark S. on Apr 18, 20 2325 6 Tjark S. Can't get a good first layer Da Peter M on Apr 18, 20 2960 5 PreZ Top Infill Sticks Out Sides Da bobstro on Apr 17, 20 2216 2 MiLkiE Prusa RC3 (A4 Variant) PETG Da bob loblaw on Apr 17, 20 2214 1 bob loblaw Perimeter before infill Da Sternmiere on Apr 17, 20 1567 1 Sternmiere The printed part moves Da pcweber on Apr 16, 20 2486 4 gtlon Issue with First Layer Da Peter M on Apr 16, 20 1893 3 Peter Parameters for diffent filaments in one print ... Da Shabratka on Apr 16, 20 1568 1 Shabratka Prints one but not multiple Da JoanTabb on Apr 16, 20 2439 8 TShelton Vertical Shifts in my print - how could i solv... Da ChristianBack on Apr 16, 20 1579 1 ChristianBack Small Footprints Great -- Large not so much Da Peter M on Apr 15, 20 2331 5 Todd Decker MK3S abl problem Da macc on Apr 14, 20 1764 1 macc Shifted layer Da Peter in Katy on Apr 14, 20 1450 2 Ladas007 replacing white tube above nozzle Da ecowaveteam on Apr 13, 20 2029 3 ecowaveteam printing round overhangs Da Peter M on Apr 13, 20 3794 7 Zaribo Owner Pagina 126 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: