English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 119 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author PETG sringing? Before all, just do this 🙂 Przez Jiheffe on Jun 14, 20 1788 1 Jiheffe PETG curling on small perimeters/overhangs Przez r3l471v157 on Jun 14, 20 5314 2 Real Downloaded pay-STL for Airplane-wingtip How To... Przez 4Unlimited on Jun 13, 20 5660 24 4Unlimited i3 MK3 Stops Extruding - PLA Printing Przez robo67 on Jun 13, 20 1392 1 robo67 how do I print this? Przez jsw on Jun 12, 20 1645 2 jariasalcala Advise printing ASA Przez Jiheffe on Jun 12, 20 1641 1 Jiheffe Issue with PLA Przez Andrew on Jun 10, 20 2354 7 jaychatt Joining multiple sections? Help please Przez Peter M on Jun 10, 20 3558 4 Tim104 Optimal settings for Inland PETG filament Przez jyviko on Jun 10, 20 5293 5 RepRapAssassi... Does my Filamentum PLA Crystal Clear hate me? Przez Andrew on Jun 09, 20 2055 1 Andrew Overhang Problems Przez Avianna on Jun 09, 20 1757 2 merty238 Frustrating BVOH printing issue Przez Mindy M. on Jun 08, 20 3556 3 Mindy M. ASA print issue Przez Zoltan on Jun 08, 20 8818 15 morrone Consecutive prints as a print run - Just curio... Przez Andrew on Jun 07, 20 1763 1 Andrew Maintain warm enclosure temperature at all tim... Przez Andrew on Jun 07, 20 2018 2 Richard63 Petg continuously clogging Przez cltaggart on Jun 06, 20 4249 3 EMC3 Gradient infill - how? Przez jsw on Jun 06, 20 3061 2 Chris P Can I vary the infill at more than one "band" ... Answered Przez Andrew on Jun 06, 20 3010 3 Andrew Layer under supports not smooth, rest of print... Przez Bunny Science on Jun 06, 20 5153 4 DamienB Incomplete perimeters Przez Bunny Science on Jun 06, 20 3901 10 Markus Strona 119 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: