Notifiche
Cancella tutti

Firmware 3.14.0 Missing Load Filament Option  

  RSS
Fredotech
(@fredotech)
Utenti
Firmware 3.14.0 Missing Load Filament Option

I upgraded to Firmware 3.14.0. and I do not have an option to Load filament.  Downgraded back to Firmware 3.13.3. I now have an option.

Postato : 31/08/2024 4:08 pm
Allen8355
(@allen8355)
Estimable Member
RE: Firmware 3.14.0 Missing Load Filament Option

If the filament sensor is ON, it will load when you load filament. If the filament sensor is OFF, I THINK the option returns.

Postato : 06/09/2024 4:23 am
Fredotech
(@fredotech)
Utenti
Topic starter answered:
RE: Firmware 3.14.0 Missing Load Filament Option

I have tried with both settings Off & On. and I cannot load filament

Postato : 18/09/2024 5:54 pm
A_R_B hanno apprezzato
RedDawg
(@reddawg)
Reputable Member
RE: Firmware 3.14.0 Missing Load Filament Option

Do you have an MMU attached? If so, turn it Off in Settings. Load Filament option should return (single filament mode).

Hear ye, Hear ye! Step right up folks and get your Government salvation here! Less than $.002 per word! Amazon.com/dp/B0B8XMMFP4

Postato : 25/09/2024 11:50 pm
Fredotech
(@fredotech)
Utenti
Topic starter answered:
RE: Firmware 3.14.0 Missing Load Filament Option

I do not .  Still did not work

Postato : 26/09/2024 3:20 am
JohnP
(@johnp)
New Member
RE:

Same here. Seriously Prusa, rather than your endless ads for your overpriced and outdated printers how about some better QA on your firmware releases.

Questo post è stato modificato 2 months fa da JohnP
Postato : 28/09/2024 9:55 am
martijnh
(@martijnh)
Active Member
RE: Firmware 3.14.0 Missing Load Filament Option

please put it back, many people are not very happy with the sensor option...

Postato : 07/10/2024 6:55 pm
peter.s e A_R_B hanno apprezzato
martijnh
(@martijnh)
Active Member
RE: Firmware 3.14.0 Missing Load Filament Option

Why is it gone? i had a lot of trouble with adjusting the stupid mk3s sensor. also problems now in selftest X-axis..

Postato : 07/10/2024 6:57 pm
A_R_B hanno apprezzato
A_R_B
(@a_r_b)
New Member
RE: Firmware 3.14.0 Missing Load Filament Option

Same here, Prusa come back to quality and clear descriptions! Please...

---
In God we trust. All others must bring data!

Postato : 14/10/2024 4:58 pm
peter.s
(@peter-s-3)
Active Member
RE: Firmware 3.14.0 Missing Load Filament Option

DO bring the load option back - please!

Postato : 17/10/2024 4:13 pm
grogan645
(@grogan645)
Utenti
RE: Firmware 3.14.0 Missing Load Filament Option

Just put my mk3s+ in an enclosure and updated firmware, now it won't feed filament, it was working just a couple of days prior. I have a new sensor board on order, but now I'm not sure if it's the board or firmware. This firmware was vetted for the for the MK3S+?

Postato : 21/10/2024 7:31 pm
Condividi: