English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 83 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Z Error following Hot End Replacement Von Mark A on Jan 28, 21 1762 4 Mark A Optimal live-z setting not the same everywhere... Von Husflid on Jan 28, 21 1916 5 Husflid First print vase from sd card inside not good Von DadOf6 on Jan 28, 21 2659 3 TommyB Top layer tweaking Von bobstro on Jan 27, 21 2225 5 KjsiderPrinte... First Layer issues: Live Z really high (or low... Von KjsiderPrinter on Jan 27, 21 2697 17 KjsiderPrinte... First Layer Adhesion issue after 100+ successf... Von Grayson72 on Jan 27, 21 3111 11 foxten X-Carriage Alignment During Assembly Von mntechnogeek on Jan 27, 21 2203 4 mntechnogeek Finally Got My Black Friday Toy - Losing Adhes... Von HDHJR on Jan 26, 21 2062 6 HDHJR Z calbration now now printing fillimate and gl... Von dauga on Jan 26, 21 1533 4 dauga wobbley layers Von SlowMaker on Jan 26, 21 2115 1 SlowMaker Blobs on first layers on first prints Von Peter M on Jan 26, 21 1722 3 Baisulis Filament wont extrude during calibration or pr... Von riptidembp on Jan 25, 21 1958 7 riptidembp Wobbly sides Answered Von Roy_T on Jan 25, 21 2859 6 Roy_T Z height, first layer and adhesion Von DusBus on Jan 25, 21 2226 2 DusBus Lifted filament from bed Von J.Ligthart on Jan 25, 21 1500 2 J.Ligthart PETG - Textured Sheet Adhesion Problem Von JoeinCal on Jan 24, 21 1727 3 JoeinCal MK3 XYZ calibration fails after upgrading to f... Von ToniP on Jan 24, 21 1535 3 ToniP First Benchy! A few problem spots though Von Robin on Jan 24, 21 2747 5 Pixel Visions First benchy, now with pics! Troubleshooting a... Von Pixel Visions on Jan 24, 21 2868 2 Pixel Visions Prusa i3 Mk3s+ Spring steel bed choice. Von Ron L on Jan 22, 21 3578 14 Ron L Seite 83 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Teilen: