English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 82 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author ptfe jam By Sam on Jan 30, 21 1890 2 haris Pretest By lapf on Jan 30, 21 1546 3 lapf Creaking of the nozzle about the product By RH_Dreambox on Jan 30, 21 1843 6 Daniel i3 MK3S+ Kit Layers Problems By cwbullet on Jan 30, 21 2025 2 JoshyMade Nozzle hitting at the end of the print? By JoanTabb on Jan 29, 21 2706 6 DadOf6 Lost in Z translation - late first layer troub... By Dan Rogers on Jan 29, 21 1909 9 Furby Goulag Worked great, until it didn't By Dan Rogers on Jan 28, 21 1429 5 BlondCE First two Benchys - am I on the right track? By DanMi on Jan 28, 21 1185 3 DanMi Z Error following Hot End Replacement By Mark A on Jan 28, 21 1487 4 Mark A Optimal live-z setting not the same everywhere... By Husflid on Jan 28, 21 1679 5 Husflid First print vase from sd card inside not good By DadOf6 on Jan 28, 21 2444 3 TommyB Top layer tweaking By bobstro on Jan 27, 21 1827 5 KjsiderPrinte... First Layer issues: Live Z really high (or low... By KjsiderPrinter on Jan 27, 21 2360 17 KjsiderPrinte... First Layer Adhesion issue after 100+ successf... By Grayson72 on Jan 27, 21 2763 11 foxten X-Carriage Alignment During Assembly By mntechnogeek on Jan 27, 21 1943 4 mntechnogeek Finally Got My Black Friday Toy - Losing Adhes... By HDHJR on Jan 26, 21 1867 6 HDHJR Z calbration now now printing fillimate and gl... By dauga on Jan 26, 21 1347 4 dauga wobbley layers By SlowMaker on Jan 26, 21 1835 1 SlowMaker Blobs on first layers on first prints By Peter M on Jan 26, 21 1499 3 Baisulis Filament wont extrude during calibration or pr... By riptidembp on Jan 25, 21 1774 7 riptidembp Page 82 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: