English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 60 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author How can i improve prints? By Pondzik on Aug 27, 21 1549 4 Pondzik Adhesiun problem, calibration issue? By JoanTabb on Aug 25, 21 1801 4 Siggi Bjarnas... Replaced heatbed thermistor now having bed adh... Answered By cwbullet on Aug 25, 21 1784 7 PetervdPerk PLA wont stick to the PEI plater Answered By BrettG on Aug 25, 21 3272 12 Gurīn First prints fine (I think) Triceratops fails ... By RandyM9 on Aug 25, 21 2321 19 navajas is this z banding? loose (or too tight?) x bel... By cwbullet on Aug 24, 21 3998 7 lumbeecheraw7... Gaps around edges By Fredrico on Aug 23, 21 1970 5 Fredrico Newb getting intermittent excessive material By cwbullet on Aug 23, 21 2329 12 LouisB Just prints a blob in the corner By Buffle on Aug 23, 21 1749 6 matthewstokey First Layer Calibration / Benchy Bottom By bobstro on Aug 23, 21 7036 5 Yangorang Noises on all axises By Peter M on Aug 22, 21 2184 5 Jakub Why is it printing a floor in mid-air? Answered By JoanTabb on Aug 21, 21 1951 8 Daniel Problem printing first few layers - filament g... By Diem on Aug 18, 21 2251 6 Makr unload and load filament over and over again Answered By cwbullet on Aug 18, 21 1587 6 Junichi Continuing first layer issues By cwbullet on Aug 17, 21 1561 6 BMet Z-Axis Dimension Calibration? By Ringarn67 on Aug 16, 21 2933 6 Yangorang mk3s Z axis problems By ah1102 on Aug 16, 21 2487 9 ah1102 Shifting in model after a few layers. By smax on Aug 16, 21 1754 6 ShRTee Bad Benchys, Please Help By Dan Rogers on Aug 15, 21 2159 6 Michelle X Axis Hard Stops By Dan Rogers on Aug 15, 21 1432 2 Mike Page 60 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: