English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 56 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Titre du sujet Dernier message Nombre de vues Messages Author 3x3 first layer print issues Par Fetzke on Oct 19, 21 1745 6 Fetzke Replaciing hotend Par Jeff on Oct 18, 21 1978 2 Jeff Vertical lines in print Par Neophyl on Oct 17, 21 2117 3 DanDi Excessive (and seemingly deliberate) oozing on... Par BogdanH on Oct 16, 21 3531 15 cdsupina X-axis rod damage after 50 hrs: Misaligned rod... Par pcweber on Oct 16, 21 3378 7 Fourninetysix First Layer Printing Problem Par Dan Rogers on Oct 15, 21 2089 13 seehma Visible Layer Lines/Arch Support Par PrntrFiend on Oct 14, 21 2587 4 PrntrFiend Filament transport - looks like a snake swallo... Par Sparkpoint on Oct 13, 21 2367 11 Sparkpoint Searching for the fancy calibration/setup post Par dceddia on Oct 12, 21 1402 1 dceddia Initial switch on failure Par Dan Rogers on Oct 12, 21 2752 15 John Leaking again Par Dan Rogers on Oct 12, 21 2483 8 gamefe X shifting at same height Par gamefe on Oct 10, 21 4024 16 gamefe Help! Par JoanTabb on Oct 10, 21 1663 4 Kelly what is causing this defect in both abs and pl... Par Dan Rogers on Oct 10, 21 2515 11 jrdpiper Extruder motor quite hot Par karl-herbert on Oct 09, 21 2292 3 Rafi Filament covering extruder - help! Par jwvaughn on Oct 09, 21 2120 6 HappyKatz Flipped pully to get Y-Axis central. Is this O... Par Larry on Oct 08, 21 1567 6 Larry MK3S+ Kit. Help I broke the EXTRUDER CABLE CLI... Par cwbullet on Oct 08, 21 1714 3 Jrmcswain Layer shift after infill Par Sprite001 on Oct 07, 21 3710 11 nivek90 Brand new assembled MK3S+ making grinding nois... Par Dan Rogers on Oct 07, 21 1562 4 drpepper Page 56 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Partager :