English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 56 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Vertical lines in print Von Neophyl on Oct 17, 21 2116 3 DanDi Excessive (and seemingly deliberate) oozing on... Von BogdanH on Oct 16, 21 3521 15 cdsupina X-axis rod damage after 50 hrs: Misaligned rod... Von pcweber on Oct 16, 21 3369 7 Fourninetysix First Layer Printing Problem Von Dan Rogers on Oct 15, 21 2086 13 seehma Visible Layer Lines/Arch Support Von PrntrFiend on Oct 14, 21 2583 4 PrntrFiend Filament transport - looks like a snake swallo... Von Sparkpoint on Oct 13, 21 2361 11 Sparkpoint Searching for the fancy calibration/setup post Von dceddia on Oct 12, 21 1402 1 dceddia Initial switch on failure Von Dan Rogers on Oct 12, 21 2746 15 John Leaking again Von Dan Rogers on Oct 12, 21 2475 8 gamefe X shifting at same height Von gamefe on Oct 10, 21 4012 16 gamefe Help! Von JoanTabb on Oct 10, 21 1659 4 Kelly what is causing this defect in both abs and pl... Von Dan Rogers on Oct 10, 21 2502 11 jrdpiper Extruder motor quite hot Von karl-herbert on Oct 09, 21 2288 3 Rafi Filament covering extruder - help! Von jwvaughn on Oct 09, 21 2113 6 HappyKatz Flipped pully to get Y-Axis central. Is this O... Von Larry on Oct 08, 21 1556 6 Larry MK3S+ Kit. Help I broke the EXTRUDER CABLE CLI... Von cwbullet on Oct 08, 21 1711 3 Jrmcswain Layer shift after infill Von Sprite001 on Oct 07, 21 3694 11 nivek90 Brand new assembled MK3S+ making grinding nois... Von Dan Rogers on Oct 07, 21 1555 4 drpepper How to assembly right? Von Dan Rogers on Oct 07, 21 2240 16 PrusaPrinters... Issue with Globing Von Josh Cagle on Oct 06, 21 1680 4 Josh Cagle Seite 56 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Teilen: