English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 4 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author BOD - Fortunately this one was easy to fix Przez jsw on Dec 05 1732 1 jsw Stubborn extruder clog Przez Diem on Dec 04 1975 2 DK1474 First post! First issue too... 🙁 Przez Robin on Nov 30 1871 8 Faris Itum Print differences in x Direction Przez Robin on Nov 29 1881 2 raepton Temperatur / Stringing Przez raepton on Nov 26 1792 3 raepton Can't Correctly Adjust PINDA Przez Mike C on Nov 24 8604 14 akerezy Prints coming up and getting XY axis failure Przez jbkmelk on Nov 21 1689 3 jbkmelk first layer print quality Przez gzhangx on Nov 18 2387 13 gzhangx Leak at nozzle Przez Diem on Nov 16 1488 3 jlc1978 Wavy brim edge Przez Paul Bowden on Nov 15 1516 3 Paul Bowden Printing starts well but eventually doesn't st... Przez samuel.jimenez on Nov 14 1296 2 samuel.jimene... How can I improve "stringing"? Przez samuel.jimenez on Nov 14 2339 16 samuel.jimene... Filament gets stuck during printing Przez Szabolcs Siebe... on Nov 10 1517 3 Szabolcs Sieb... inside perimeter not sticking to buildplate Answered Przez disconnected on Nov 09 1520 6 disconnected PLA not sticking??? Przez Diem on Nov 04 57190 85 travis.c5 Printer skips a few centimeters on start of ev... Przez Mathew Baldwin on Oct 24 6167 25 Justinas Is this bed leveling good? Przez gzhangx on Oct 17 1766 1 gzhangx Print quality was good, but not any more Przez gzhangx on Oct 15 1995 2 Stoffel First layer issues edges curling Przez jbkmelk on Oct 15 1899 3 jbkmelk Inconsistent Prusament ASA extrusion? Przez Perro on Oct 06 2192 5 Perro Strona 4 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: