English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 47 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Help with diagnosing what is happening Przez Aaronc321 on Jan 27, 22 2405 5 Terry G Layer problems Przez adamemme on Jan 26, 22 1514 1 adamemme Gaps Between layers and rolling of material on... Przez Diem on Jan 24, 22 2022 4 Karl Sig support scaring... need some advice Przez Bob on Jan 24, 22 3211 10 Mustache_Gami... 3D Benchy Troubleshooting help Przez SmadaPrinting on Jan 24, 22 2622 3 SmadaPrinting Newb xyz calibration fail Answered Przez nate on Jan 24, 22 1746 6 nate Cold pull eval after giant blob clog Przez Bob on Jan 24, 22 2050 7 surfman49 minor 0.25 mm nozzle first layer issue, lines ... Answered Przez Milazzone on Jan 23, 22 2454 7 Milazzone Newbie first project with PC problem Answered Przez RinkyTav on Jan 22, 22 2164 5 RinkyTav Z-offset and bed leveling Przez Kavan on Jan 22, 22 2433 3 Kavan Gaps between lines in layers Przez Karl Sig on Jan 21, 22 6744 7 m0dule Filament sensor lever-matte finish? Przez stephen.h14 on Jan 21, 22 2171 4 stephen.h14 Need help determining my z height Przez Bob on Jan 20, 22 2751 7 rangertown Opinions on this PETG Przez dorkshoei on Jan 20, 22 1685 1 dorkshoei Zip-ties on assembled printer Przez bobstro on Jan 20, 22 2060 2 Cornmeister Print just stops mid-print - no indication - b... Answered Przez mgtarallo on Jan 18, 22 2256 7 mgtarallo Support material Przez Robin on Jan 18, 22 2103 13 drb1515 Ooz settings Przez cwbullet on Jan 18, 22 1612 3 bulgiz Support material top layer Przez bulgiz on Jan 18, 22 1531 3 bulgiz Is this normal?? Przez Tim Weston on Jan 17, 22 1059 2 lgclemens Strona 47 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: