English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 45 / 216 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Crazy Horrible Prints - Please Help!! Da Robin on Jan 31, 22 2335 7 NoahEdwards print issues Da Bob on Jan 28, 22 1398 3 iktwo Anything I should be concerned about here? (ov... Da Rick Lohr on Jan 28, 22 5683 44 Rick Lohr Nozzle dragging? - Only on one part of the bed... Answered Da mgtarallo on Jan 28, 22 2140 4 mgtarallo Bad top layer Da Sinled on Jan 27, 22 3169 15 tbbtrocks Batman logo imperfections Da Robin on Jan 27, 22 1968 7 Smart-site Help with diagnosing what is happening Da Aaronc321 on Jan 27, 22 1874 5 Terry G Layer problems Da adamemme on Jan 26, 22 1208 1 adamemme Gaps Between layers and rolling of material on... Da Diem on Jan 24, 22 1573 4 Karl Sig Prusa logo first print, is the Z offset good? Da Andrew on Jan 24, 22 2064 12 blank_dvth support scaring... need some advice Da Bob on Jan 24, 22 2423 10 Mustache_Gami... 3D Benchy Troubleshooting help Da SmadaPrinting on Jan 24, 22 2203 3 SmadaPrinting Newb xyz calibration fail Answered Da nate on Jan 24, 22 1431 6 nate Cold pull eval after giant blob clog Da Bob on Jan 24, 22 1434 7 surfman49 minor 0.25 mm nozzle first layer issue, lines ... Answered Da Milazzone on Jan 23, 22 1873 7 Milazzone Newbie first project with PC problem Answered Da RinkyTav on Jan 22, 22 1748 5 RinkyTav Z-offset and bed leveling Da Kavan on Jan 22, 22 1948 3 Kavan Gaps between lines in layers Da Karl Sig on Jan 21, 22 6027 7 m0dule Filament sensor lever-matte finish? Da stephen.h14 on Jan 21, 22 1637 4 stephen.h14 Need help determining my z height Da Bob on Jan 20, 22 2090 7 rangertown Pagina 45 / 216 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Avanti Condividi: