English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 45 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Thumps once at startup Por alianora on Feb 19, 22 1613 3 alianora mintemp error, hotend killed ? Por Max on Feb 19, 22 6384 23 Max what is this? Por Bob on Feb 18, 22 1871 8 John Is my x-belt tension too loose? Por xilex on Feb 18, 22 2087 3 xilex First layer problem with PETG - Irregular resu... Answered Por Txema on Feb 17, 22 3964 8 Txema Oops, success, oops again ... Por Diem on Feb 17, 22 3128 14 RoDavi recalibration? Por Diem on Feb 17, 22 1870 4 John What is a purpose of this nuts? Answered Por livius on Feb 15, 22 1953 4 livius Any idea whats wrong with my top layer? Por Robin on Feb 15, 22 1845 3 Zalgus First Layer Callibration Answered Por surgebox on Feb 15, 22 2073 4 surgebox Bed leveling question with these leveling valu... Answered Por Diem on Feb 15, 22 1873 4 xilex Odd Printing Issue Por cwbullet on Feb 15, 22 1825 2 durrettcustom... Waves in first layer Answered Por HappyKatz on Feb 14, 22 5569 5 HappyKatz Mk3S and adding MMU2.5S Assembly Instructions Por MikeJ on Feb 14, 22 1865 5 MikeJ First print not from a test file Por Bob on Feb 12, 22 2632 7 RoDavi Schnellgang prusa i3 mks3s+ Por baeru on Feb 12, 22 1477 1 baeru Noise Levels in Standard Mode Por HenrikLager on Feb 12, 22 6487 9 Pezmc Z-Axis seems too stretched Por a_patch on Feb 11, 22 1910 4 lostretrotape... One calibration point is bad Por Bob on Feb 11, 22 1782 2 Pas0li New kit MK3S+ first layer problem Por Bob on Feb 11, 22 2203 5 livius Página 45 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: