English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 4 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Printer skipping area of layers Answered Od enganear on Dec 17 7409 27 Noel Failing when multiple objects Od nzxela on Dec 15 4258 6 Mallonum Corners Lifting During Prints Od icestationz on Dec 14 12554 6 sleepysnorlax Recalibration from scratch after replacing PTF... Answered Od DMayfield on Dec 10 2533 9 FIX6 Bad Print Od parallon on Dec 08 1797 2 parallon Printer Stand Od Diem on Dec 07 2094 4 akerezy BOD - Fortunately this one was easy to fix Od jsw on Dec 05 1828 1 jsw Stubborn extruder clog Od Diem on Dec 04 2114 2 DK1474 First post! First issue too... 🙁 Od Robin on Nov 30 2081 8 Faris Itum Print differences in x Direction Od Robin on Nov 29 2060 2 raepton Temperatur / Stringing Od raepton on Nov 26 1978 3 raepton Can't Correctly Adjust PINDA Od Mike C on Nov 24 8880 14 akerezy Prints coming up and getting XY axis failure Od jbkmelk on Nov 21 1801 3 jbkmelk first layer print quality Od gzhangx on Nov 18 2514 13 gzhangx Leak at nozzle Od Diem on Nov 16 1597 3 jlc1978 Wavy brim edge Od Paul Bowden on Nov 15 1635 3 Paul Bowden Printing starts well but eventually doesn't st... Od samuel.jimenez on Nov 14 1365 2 samuel.jimene... How can I improve "stringing"? Od samuel.jimenez on Nov 14 2483 16 samuel.jimene... Filament gets stuck during printing Od Szabolcs Siebe... on Nov 10 1583 3 Szabolcs Sieb... inside perimeter not sticking to buildplate Answered Od disconnected on Nov 09 1668 6 disconnected Stránka 4 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Share: