English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 31 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Cant get past Calibrate XYZ without paper movi... Przez Diem on Sep 06, 22 1300 3 3dPrinterGoBo... Distorted Benchy with banding 🙁 (first print) Przez ormstont on Sep 06, 22 2166 9 ormstont Inclined nozzle - cause of problem? how to fix... Answered Przez Pfriemler on Sep 05, 22 2447 10 Pfriemler I3 Mk3s+ kit massive stringing issues Przez The Astrononee... on Sep 05, 22 1217 5 The Astronone... Assembled kit, printed a whistler, no issues, ... Przez RandyM9 on Sep 04, 22 1581 9 J D Post Clog Configuration Przez RandyM9 on Sep 03, 22 1374 6 wearethehive Layers not aligned x and y Przez MarcWinNJ on Sep 03, 22 2071 3 Dan Albino is this too loud or normal? Przez Eric E on Sep 03, 22 1132 3 J D Stringing and Holes - HELP 🙁 Przez LindsKay on Sep 02, 22 2239 7 LindsKay Can you help me to identify what the problem i... Przez Robin on Sep 01, 22 1523 4 RoboMan Horizontal lines problems Przez treedee on Aug 30, 22 10234 29 treedee First Layer Height Intermittent [Live Adjust Z... Przez MakotoNinja on Aug 29, 22 1806 5 MakotoNinja Problems with first articulated print Przez Neophyl on Aug 29, 22 1571 3 josensei error "calibrations failed, check axis..." Przez lynellephi on Aug 29, 22 1568 8 lynellephi Brand New (wet?) Prusament PLA Filament Przez jsw on Aug 28, 22 2129 3 josensei Is this stringing worth trying to reduce? Answered Przez zukpr on Aug 27, 22 1816 4 zukpr Rattle noise Przez Falangsaywhat on Aug 27, 22 6552 9 CH PSU bad??? Just completed kit -- won't power o... Przez Ready4Launch on Aug 25, 22 2206 17 Ready4Launch X/Y Axis Slightly Skewed After XYZ Recal Przez Your Fave Mull... on Aug 24, 22 1608 1 Your Fave Mul... Mk3s+ kit ptfe Przez RandyM9 on Aug 24, 22 1341 5 giodee Strona 31 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: