English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 32 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author First prints following upgrade from MK3S to MK... Przez cwbullet on Sep 21, 22 1827 4 Tekin Ozbek Prusa i3 MK3S+ after final assambly not turn o... Przez karl-herbert on Sep 16, 22 1881 4 PrusaPrinters... Filament sensor wiring error Przez JoanTabb on Sep 16, 22 5256 10 thomas.a21 Filament sensor wiring error MK3 Przez cwbullet on Sep 16, 22 2920 2 Petver62 Can't get anything to stick Answered Przez P.O. on Sep 15, 22 2185 9 oobedoob Problème d'impression première couche PETG Przez Jacques Rigal on Sep 15, 22 2757 4 Jacques Rigal Help just finished building printer Przez Netpackrat on Sep 14, 22 2023 5 Christopher P... A quick sigh of relief and thanks Przez RandyM9 on Sep 11, 22 1807 3 Baz First Prints Przez Neophyl on Sep 11, 22 1672 11 daveetch rough sidewalls Przez SFilipp on Sep 10, 22 1562 3 SFilipp New printer, X axis out of alignment on first ... Answered Przez Greysoul on Sep 08, 22 1449 5 Greysoul Help requested: First Layer Calibration: "some... Answered Przez Joe on Sep 07, 22 1716 2 Joe Cant get past Calibrate XYZ without paper movi... Przez Diem on Sep 06, 22 1775 3 3dPrinterGoBo... Distorted Benchy with banding 🙁 (first print) Przez ormstont on Sep 06, 22 2972 9 ormstont Inclined nozzle - cause of problem? how to fix... Answered Przez Pfriemler on Sep 05, 22 3698 10 Pfriemler I3 Mk3s+ kit massive stringing issues Przez The Astrononee... on Sep 05, 22 1560 5 The Astronone... Assembled kit, printed a whistler, no issues, ... Przez RandyM9 on Sep 04, 22 2241 9 J D Post Clog Configuration Przez RandyM9 on Sep 03, 22 1990 6 wearethehive Layers not aligned x and y Przez MarcWinNJ on Sep 03, 22 2569 3 Dan Albino is this too loud or normal? Przez Eric E on Sep 03, 22 1452 3 J D Strona 32 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: